Infiniti F50. Manual — part 656
INTERIOR ROOM LAMP
LT-91
C
D
E
F
G
H
I
J
L
M
A
B
LT
TKWM0349E
LT-92
INTERIOR ROOM LAMP
Terminals and Reference Value for BCM
EKS00174
Terminal
No.
Wire
color
Signal description
Measuring condition
Voltage
(Approximate values)
Ignition
switch
Operation or condition
17
BR/Y
Data link RX
—
—
—
18
P
Data link TX
—
—
—
30
PU
Communication signal TX
(BCM-AV: Transmission)
—
—
—
31
LG
Communication signal RX
(AV-BCM: Receiving)
—
—
—
33
W
Rear LH door switch signal
OFF
Rear LH door switch
ON (open)
Less than 1V
OFF (closed)
Battery voltage
37
W/G
Passenger door switch signal
OFF
Passenger door switch
ON (open)
Less than 1V
OFF (closed)
Battery voltage
56
B
Ground
—
—
—
60
L/OR
ACC power supply
ACC
—
Battery voltage
67
G/W
LAN communication
—
—
—
68
W/B
IGN power supply
ON
—
Battery voltage
69
PU/W
Key switch and key lock solenoid
signal
OFF
Key withdrawn (OFF)
Less than 1V
Key inserted (ON)
Battery voltage
105
Y/L
BAT power supply
OFF
—
Battery voltage
110
SB
Ignition switch illumination signal
OFF
Turned OFF
Battery voltage
Turned ON
Less than 1V
113
B
Ground
—
—
—
129
G
Personal lamp switch signal
OFF
Personal lamp switch
One switch ON
5V
AUTO
5V
Both switch ON
Less than 1V
130
W/L
Interior lamp ill switch ON signal
OFF
Interior lamp ill switch
ON
Less than 1V
AUTO
5V
OFF
5V
131
G/Y
Interior lamp ill switch OFF sig-
nal
OFF
Interior lamp ill switch
ON
5V
AUTO
5V
OFF
Less than 1V
133
Y/R
Map lamp LH signal
OFF
Turned OFF
Battery voltage
Dimming
8V
Turned ON
Less than 1V
137
OR
Personal lamp RH signal
OFF
Turned OFF
Battery voltage
Dimming
8V
Turned ON
Less than 1V
138
G/R
Personal lamp LH signal
OFF
Turned OFF
Battery voltage
Dimming
8V
Turned ON
Less than 1V
140
Y/B
Map lamp RH signal
OFF
Turned OFF
Battery voltage
Dimming
8V
Turned ON
Less than 1V
INTERIOR ROOM LAMP
LT-93
C
D
E
F
G
H
I
J
L
M
A
B
LT
Terminals and Reference Value for Driver Door Control Unit (LCU01)
EKS000X0
Work Flow
EKS000X1
1.
Confirm the symptom or customer complaint.
2.
Understand system description. Refer to
3.
Perform the preliminary check. Refer to
4.
Does the door lock system operate normally? When yes, go to step 5. When no, go to Power door lock
system
in “BODY LOCK & SECURITY SYSTEM (BL)” section.
5.
Find the cause of trouble following the trouble diagnosis chart by symptom and repair or replace as neces-
sary. Refer to
6.
Does the total coordinated interior illumination operate normally? When yes, go to step 7. When no, go to
step 5.
7.
Inspection end.
Preliminary Check
EKS000X2
SETTING CHANGE FUNCTION
●
Setting for each operation can be changed using CONSULT-II and a display unit.
CAUTION:
After the setting is changed, the new setting will be maintained even if the battery is disconnected.
142
W/R
Driver door switch signal
OFF
Driver door switch
ON (open)
Less than 1V
OFF (closed)
Battery voltage
143
W/L
Rear RH door switch signal
OFF
Rear RH door switch
ON (open)
Less than 1V
OFF (closed)
Battery voltage
Terminal
No.
Wire
color
Signal description
Measuring condition
Voltage
(Approximate values)
Ignition
switch
Operation or condition
Terminal
No.
Wire
color
Item
Condition
Voltage
(Approximate values)
6
G/Y
Door unlock sensor
OFF (Locked)
→
ON (unlocked)
5V
→
0V
8
G/W
Data line A-3
—
—
14
Y/G
Power source (PTC)
—
Battery voltage
15
B
Ground
—
0V
Item
Description
CONSULT-II
(Work support)
Display unit
(Setting of various vehicle
conditions)
Factory
setting
SET I/L LGC-D- UNLCK (CONSULT-II)
Illuminate Interior When Unlocking
Vehicle (display unit)
Selects ON-OFF of the
interior lamp illumination
at the time the driver
door is unlocked.
ON
ON: Indicator ON
×
OFF
OFF: indicator OFF
—
SET INT- L LOGIC-TIM (CONSULT-II)
Interior Lights Off Delay (display unit)
Selects interior lamp
timer set time in four
steps.
Mode 1 (off)
OFF: Display OFF
—
Mode 2 (15 seconds)
15 seconds: Display 15 sec.
—
Normal (30 seconds)
30 seconds: Display 30 sec.
×
Mode 3 (45 seconds)
45 seconds: Display 45 sec.
—
LT-94
INTERIOR ROOM LAMP
INSPECTION FOR POWER AND GROUND CIRCUIT
1.
FUSE CHECK
Check if any of the following fuses in BCM are blown.
OK or NG
OK
>> GO TO 2.
NG
>> If fuse is blown, be sure to eliminate cause of malfunction before installing new fuse.
2.
CHECK POWER SUPPLY CIRCUIT
1.
Disconnect the BCM connector and driver door LCU connector.
2.
Check voltage between the following harness connector termi-
nals and ground.
OK or NG
OK
>> GO TO 3.
NG
>> Check harness for open or short between BCM or driver
door LCU and fuse.
Unit
Power source
Terminal
Fuse No.
BCM
Battery power supply
105
3
ACC power supply
60
21
IGN power supply
68
1
Unit
Terminals
(Wire color)
Power source
condition
Voltage
Connector
(+)
(–)
BCM (M4)
105 (Y/L)
Body
ground
Battery power
supply
Ignition
switch OFF
Battery
voltage
68 (W/B)
IGN power
supply
Ignition
switch ON
Battery
voltage
Driver door
LCU (D8)
14 (Y/G)
Battery power
supply
Ignition
switch OFF
Battery
voltage
SKIA3930E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст