Infiniti F50. Manual — part 731
SERVICE DATA AND SPECIFICATIONS (SDS)
RFD-29
C
E
F
G
H
I
J
K
L
M
A
B
RFD
Drive Pinion Height Adjustment
EDS000YS
AVAILABLE PINION HEIGHT ADJUSTING WASHERS
Unit: mm (in)
Drive Pinion Preload Adjustment
EDS000YT
Side Bearing Preload Adjustment
EDS000YU
SIDE BEARING ADJUSTING WASHERS
Unit: mm (in)
Total Preload Adjustment
EDS000YV
Type
R200, R200V
Adjusting washer
Thickness
Part number
Thickness
Part number
3.05 (0.1201)
38154 0C000
3.29 (0.1295)
38154 0C008
3.08 (0.1213)
38154 0C001
3.32 (0.1307)
38154 0C009
3.11 (0.1224)
38154 0C002
3.35 (0.1319)
38154 0C010
3.14 (0.1236)
38154 0C003
3.38 (0.1331)
38154 0C011
3.17 (0.1248)
38154 0C004
3.41 (0.1343)
38154 0C012
3.20 (0.1260)
38154 0C005
3.44 (0.1354)
38154 0C013
3.23 (0.1272)
38154 0C006
3.47 (0.1366)
38154 0C014
3.26 (0.1283)
38154 0C007
3.50 (0.1378)
38154 0C015
Type
R200
Drive pinion preload
2.65
−
3.23 N·m (0.27
−
0.32 kg
−
m, 24
−
28 in lb)
Type
R200
Side bearing preload <Reference>
0.20
−
0.52 N·m (0.02
−
0.05 kg
−
m, 2
−
4 in lb)
Torque by spring gauge
34.2
−
39.2 N (3.5
−
4 kg, 7.7
−
8.8 lb)
Type
R200
Adjusting washer
Thickness
Part number
Thickness
Part number
2.00 (0.0787)
38453 N3100
2.35 (0.0925)
38453 N3107
2.05 (0.0807)
38453 N3101
2.40 (0.0945)
38453 N3108
2.10 (0.0827)
38453 N3102
2.45 (0.0965)
38453 N3109
2.15 (0.0846)
38453 N3103
2.50 (0.0984)
38453 N3110
2.20 (0.0866)
38453 N3104
2.55 (0.1004)
38453 N3111
2.25 (0.0886)
38453 N3105
2.60 (0.1024)
38453 N3112
2.30 (0.0906)
38453 N3106
2.65 (0.1043)
38453 N3113
Type
R200
Total preload with oil seal
2.84
−
3.75 N·m (0.29
−
0.38 kg
−
m, 26
−
33 in lb)
Ring gear to drive pinion backlash
0.10
−
0.15 mm (0.0039
−
0.0059 in)
RFD-30
SERVICE DATA AND SPECIFICATIONS (SDS)
RSU-1
REAR SUSPENSION
E SUSPENSION
CONTENTS
C
D
F
G
H
I
J
K
L
M
SECTION
A
B
RSU
REAR SUSPENSION
PRECAUTIONS . . . . . . . . . . . . . . .. 2
Cautions . . . . . . . . . . . . . . . . ... 2
PREPARATION . . . . . . . . . . . . . . ... 3
Special Service Tools . . . . . . . . . . . ... 3
Commercial Service Tools . . . . . . . . . . 3
NOISE, VIBRATION AND HARSHNESS (NVH)
TROUBLESHOOTING . . . . . . . . . . . . 4
NVH Troubleshooting Chart . . . . . . . . . . 4
REAR SUSPENSION ASSEMBLY . . . . . . . . 5
Components . . . . . . . . . . . . . . . . 5
On-Vehicle Inspection and Service . . . . . . .. 6
INSPECTION OF BALL JOINT END PLAY . . .. 6
SHOCK ABSORBER INSPECTION . . . . . . 6
Wheel Alignment Inspection . . . . . . . . . . 6
SHOCK ABSORBER . . . . . . . . . . . . .. 9
Removal and Installation . . . . . . . . . . .. 9
Disassembly and Assembly . . . . . . . . . . 9
SUSPENSION ARM . . . . . . . . . . . . ..11
Removal and Installation . . . . . . . . . . .11
RADIUS ROD . . . . . . . . . . . . . . . 13
Removal and Installation . . . . . . . . . . 13
FRONT LOWER LINK . . . . . . . . . . . .. 14
Removal and Installation . . . . . . . . . . 14
REAR LOWER LINK & COIL SPRING . . . . . . 15
Removal and Installation . . . . . . . . . . 15
STABILIZER BAR . . . . . . . . . . . . . . 16
Removal and Installation . . . . . . . . . . 16
REAR SUSPENSION MEMBER . . . . . . . ... 17
Removal and Installation . . . . . . . . . . 17
RSU-2
PRECAUTIONS
PRECAUTIONS
PFP:00001
Cautions
EES000U6
●
When installing rubber bushings, final tightening must be carried out under unladen condition with tires on
level ground. Oil will shorten the life of rubber bushings. Be sure to wipe off any spilled oil.
●
Unladen condition means that fuel, coolant and lubricant are full. Spare tire, jack, hand tools and mats in
designated positions.
●
After servicing suspension parts, be sure to check wheel alignment.
●
Caulking nuts are not reusable. Always use new ones when installing. Since new caulking nuts are pre-
oiled, tighten as they are.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст