Infiniti F50. Manual — part 791
HEATED SEAT
SE-155
C
D
E
F
G
H
J
K
L
M
A
B
SE
Rear Heated Seat Switch Low Circuit Inspection
EIS003W3
1.
CHECK REAR HEATER SWITCH POWER SUPPLY
1.
Turn ignition switch ON.
2.
Check voltage between rear power seat control unit connector
and ground.
OK or NG
OK
>> Replace rear power seat control unit.
NG
>> When turn ignition switch ON and heater switch LOW, check the following.
●
When voltage is approx. 0V, GO TO 2.
●
When voltage is approx. 5V, GO TO 3.
2.
CHECK REAR POWER SEAT SWITCH (HEATER SWITCH) HEATER HARNESS
1.
Turn ignition switch OFF.
2.
Disconnect rear seat control unit connector and rear power seat
switch (heater switch) connector.
3.
Check continuity between rear seat control unit connector B163
(LH), B363 (RH) terminal 32 (LG/W) and ground.
OK or NG
OK
>> Replace rear power seat control unit.
NG
>> Repair or replace harness between rear power seat con-
trol unit and rear power seat switch (heater switch).
3.
CHECK REAR POWER SEAT SWITCH (HEATER SWITCH) HEATER HARNESS
1.
Turn ignition switch OFF.
2.
Disconnect rear power seat control unit connector and rear
power seat switch (heater switch) connector.
3.
Check continuity between rear power seat control unit connector
B163 (LH), B363 (RH) terminal 32 (LG/W) and rear power seat
switch (heater switch) connector D55 (LH), D75 (RH) terminal 5
(L/W) (LH), 6 (Y/R) (RH).
OK or NG
OK
>> GO TO 4.
NG
>> Repair or replace harness between rear power seat control unit and rear power seat switch
(heater switch).
Con-
nector
Terminal
(Wire color)
Condition
Voltage (V)
(Approx.)
(+)
(–)
B163
(LH),
B363
(RH)
32 (LG/W)
Ground
Turn ignition switch ON.
Heater switch LOW.
0
Heater switch OFF.
5
PIIA4043E
32 (LG/W)
−
Ground
:Continuity should not exist
PIIA4044E
Rear seat LH
32 (LG/W)
−
5 (L/W)
:Continuity should exist
Rear seat RH
32 (LG/W)
−
6 (Y/R)
:Continuity should exist
PIIA4045E
SE-156
HEATED SEAT
4.
CHECK REAR POWER SEAT SWITCH (HEATER SWITCH)
Check continuity between rear power seat switch (heater switch).
OK or NG
OK
>> Check the condition of the harness and connector.
NG
>> Replace rear power seat switch (heater switch).
Rear Heated Seat Switch High Circuit Inspection
EIS003WA
1.
CHECK REAR HEATER SWITCH POWER SUPPLY
1.
Turn ignition switch ON.
2.
Check voltage between rear power seat control unit connector
and ground.
OK or NG
OK
>> Rear heated seat HIGH circuit inspection is OK.
NG
>> When turn ignition switch ON and heater switch HIGH, check the following.
●
When voltage is approx. 0V, GO TO 2.
●
When voltage is approx. 5V, GO TO 3.
2.
CHECK REAR POWER SEAT SWITCH (HEATER SWITCH) HEATER HARNESS
1.
Turn ignition switch OFF.
2.
Disconnect rear seat control unit connector and rear power seat
switch (heater switch) connector.
3.
Check continuity between rear seat control unit connector B163
(LH), B363 (RH) terminal 22 (L/W) and ground.
OK or NG
OK
>> Replace rear power seat control unit.
NG
>> Repair or replace harness between rear power seat con-
trol unit and rear power seat switch (heater switch).
Terminal
Condition
Continuity
5 (LH)
6 (RH)
2
Rear heater switch LOW.
YES
Other than above.
NO
PIIA4046E
Con-
nector
Terminal
(Wire color)
Condition
Voltage (V)
(Approx.)
(+)
(–)
B163
(LH),
B363
(RH)
22 (L/W)
Ground
Turn ignition switch ON.
Heater switch HIGH.
0
Heater switch OFF.
5
PIIA4047E
22 (L/W)
−
Ground
:Continuity should not exist
PIIA4048E
HEATED SEAT
SE-157
C
D
E
F
G
H
J
K
L
M
A
B
SE
3.
CHECK REAR POWER SEAT SWITCH (HEATER SWITCH) HEATER HARNESS
1.
Turn ignition switch OFF.
2.
Disconnect rear power seat control unit connector and rear
power seat switch (heater switch) connector.
3.
Check continuity between rear power seat control unit connector
B163 (LH), B363 (RH) terminal 22 (L/W) and rear power seat
switch (heater switch) connector D55 (LH), D75 (RH) terminal 5
(L/W) (RH), 6 (Y/R) (LH).
OK or NG
OK
>> GO TO 4.
NG
>> Repair or replace harness between rear power seat control unit and rear power seat switch
(heater switch).
4.
CHECK REAR POWER SEAT SWITCH (HEATER SWITCH)
Check continuity between rear power seat switch (heater switch).
OK or NG
OK
>> Check the condition of the harness and connector.
NG
>> Replace front power seat switch (heater switch).
Rear Heated Seat Ground Circuit Inspection
EIS003YI
1.
CHECK REAR SEAT BACK HEATER HARNESS
1.
Turn ignition switch OFF.
2.
Disconnect rear seat control unit connector.
3.
Check continuity between rear seat control unit connector B162
(LH), B362 (RH) terminal 8 (OR) and 15 (B).
OK or NG
OK
>> Check the condition of the harness and connector.
NG
>> Replace rear power seat control unit.
Rear seat LH
22 (L/W)
−
6 (Y/R)
:Continuity should exist
Rear seat RH
22 (L/W)
−
5 (L/H)
:Continuity should exist
PIIA4049E
Terminal
Condition
Continuity
5 (RH)
6 (LH)
2
Rear heater switch HIGH.
Should exist
Other than above.
Should not exist
PIIA4046E
8 (OR)
−
15 (B)
:Continuity should exist
PIIA4124E
SE-158
CLIMATE CONTROLLED SEAT
CLIMATE CONTROLLED SEAT
PFP:870U6
System Description
EIS0043O
The climate controlled seat system is controlled by climate controlled seat control unit.
Heating and cooling are possible for a Thelma electric device (heat conversion machine).
NOTE:
●
The climate controlled seat system is downed when the temperature sensor set as the seat cushion and
the seat back's thermal electric device machine detects 20
°
C (68
°
F)or more of mutual differences of tem-
perature.
●
In this case, by turning off ignition switch, system down is canceled and it can be reused by turning on
ignition switch again.
●
The climate controlled seat blower keep low speed for approximately 60 seconds after turning the temper-
ature switch or the dial.
CAUTION:
●
The thermal electric device has the character in which, as for an opposite side. one side becomes
high temperature at the time of low temperature.
●
At the time of work, please turn OFF a switch, and carry it out after checking that the thermal elec-
tric device has got cold.
Power is at all times supplied
●
through 15A fuse [No. 71, and 72, located in the fuse fusible link and relay unit]
●
to climate controlled seat relay terminals 5 and 7.
When the ignition switch turned to ON or START position,
Power is supplied
●
through 10A fuse [No. 1, located in the fuse block (J/B)]
●
to climate controlled seat relay terminal 2,and
●
to climate controlled seat control unit (driver side and passenger side) terminal JD.
Then ground is supplied
●
to climate controlled seat relay terminal 1,
●
through body grounds E42, and E 62,
Then climate controlled seat relay is energized,
When climate controlled seat relay is turned to ON,
Power is supplied,
●
through climate controlled seat relay terminal 3,
●
to driver side climate controlled seat control unit terminal JB.
When climate controlled seat relay is turned to ON,
Power is supplied,
●
through climate controlled seat relay terminal 6,
●
to passenger side climate controlled seat control unit terminal JB.
When climate controlled switch select “HEAT”, ground is supply
●
through climate controlled seat switch terminal J6,
●
to climate controlled seat control unit terminal J6,
●
through climate controlled seat switch terminal JCA,
●
through body grounds B17 and B57.
Then, the climate controlled control unit receives climate controlled switch “HEAT” signal.
When climate controlled switch select “COOL”, ground is supply
●
through climate controlled seat switch terminal J16,
●
to climate controlled seat control unit terminal J16,
●
through climate controlled seat switch terminal JCA,
●
through body grounds B17 and B57.
Then, the climate controlled control unit receives climate controlled switch “COOL” signal.
When the climate controlled seat control unit receives climate controlled seat switch signal, power is supply
●
to climate controlled seat temperature dial terminal J7,
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст