Infiniti F50. Manual — part 330
CLOCK
DI-163
C
D
E
F
G
H
I
J
L
M
A
B
DI
CLOCK
PFP:25820
Wiring Diagram — CLOCK —
EKS001B7
TKWM0428E
DI-164
CLOCK
Removal and Installation
EKS001B8
REMOVAL
1.
Remove the cluster lid C, refer to
2.
Remove the screws (2), and remove clock.
INSTALLATION
Install in the reverse order of removal.
PKIA0309E
REAR VIEW MONITOR
DI-165
C
D
E
F
G
H
I
J
L
M
A
B
DI
REAR VIEW MONITOR
PFP:28260
System Description
EKS0012G
●
The rear view monitor is equipped to check the rearward of the vehicle with display when A/T selector
lever is in reverse position.
●
The lines of vehicle sides and the distance from the rear end of the vehicle are provided on display as a
guide. It allows the driver to know the distance between the vehicle and a rearward object, and the width
of the vehicle much easier.
POWER SUPPLY AND GROUND
Power is supplied at all time
●
through 15A fuse [No. 52, located in fuse, fusible link and relay block (J/B)]
●
to rear view camera control unit terminal 2.
When ignition switch is ACC or ON position, power is supplied
●
through 10A fuse [No. 21, located in fuse block (J/B) No. 1]
●
to rear view camera control unit terminal 4.
When Ignition switch is ON or START position, power is supplied
●
through 10A fuse [No. 9, located in fuse block (J/B) No. 1]
●
to back-up lamp relay terminal 2 and 5.
Ground is supplied
●
to rear view camera control unit terminal 1
●
through grounds B217 and B256, and
●
to rear view camera terminal 2
●
through grounds B17 and B57.
AV COMMUNICATION LINE
Rear view camera control unit is connected to the following units with AV communication line. Each unit trans-
mits/receives data with AV communication line.
●
AV and NAVI control unit (with navigation system)
●
AV control unit (without navigation system)
●
Display
●
Multifunction switch
REAR VIEW CAMERA OPERATION
When A/T selector lever is reverse position, power is supplied
●
through back-up lamp relay terminal 1
●
to TCM terminal 41.
Then back-up lamp relay is energized,
●
from back-up lamp relay terminal 3
●
to rear view camera control unit terminal 10.
Then, rear view camera control unit is sent camera ON signal
●
through rear view camera control unit terminal 6
●
to rear view camera terminal 1.
An image taken by rear view camera is sent
●
through rear view camera terminals 3 and 4
●
to rear view camera control unit terminals 18 and 16.
Then an image is sent
●
through rear view camera control unit terminals 22 and 24
●
to the display terminals 9 and 10.
An image of rear view will be projected on the display.
DI-166
REAR VIEW MONITOR
Rear View Camera Guide Line
When A/T selector lever is in reverse position, AV and NAVI control unit (with navigation system) or AV control
unit (without navigation system) is sent rear view camera guideline signal with AV communication line
●
from AV and NAVI control unit terminals 44 and 45 (with navigation system) or AV control unit terminal 47
and 48 (without navigation system)
●
through display, multifunction switch, audio unit and audio amp. (Bose speaker amp.)
●
to rear view camera control unit terminal 11and 9.
Then rear view camera control unit is sent rear view camera guideline image
●
through rear view camera control unit terminals 22 and 24
●
to the display terminals 9 and 10.
Rear view camera guide line will be projected on the display.
Display shows image from rear view camera image and rear view camera guideline.
FUNCTION OF BACKLIGHT CORRECTION
When visibility of rear view image projected on the display is not good caused by backlight, the rear view
image projected on the display can be adjusted by pushing “ENTER” button.
When “ENTER” button is pushed, using AV communication line, backlight correction signal is sent
●
from multifunction switch terminals 12 and 13
●
through BOSE speaker amp. and audio unit
●
to rear view camera control unit terminals 11 and 9.
Then, backlight correction signal is sent
●
through rear view camera control unit terminal 8
●
to rear view camera terminal 5.
An iris function of rear view camera will be operated, and visibility of rear view image projected on the display
will be imaged.
Component Parts and Harness Connector Location
EKS0012H
CKIM0007E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст