Infiniti F50. Manual — part 638
HEADLAMP (FOR USA)
LT-19
C
D
E
F
G
H
I
J
L
M
A
B
LT
135
Y/G
RAP output signal
OFF
When headlamp battery saver timer is
operated.
Less than 1V
142
W/R
Driver door switch signal
OFF
Driver door
switch
ON (open)
Less than 1V
OFF (close)
Battery voltage
Terminal
NO.
Wire
color
Item
Measuring condition
Reference value
(Approximate values)
Ignition
switch
Operation or condition
LT-20
HEADLAMP (FOR USA)
Work Flow
EKS0014U
1.
Confirm the symptom or customer complaint.
2.
Understand system description. Refer to
3.
Perform the preliminary check. Refer to
4.
Find the cause of trouble following the symptom chart and repair or replace as necessary. Refer to
5.
Does the auto light system operate normally? When yes, go to step 6. When no, go to step 4.
6.
Inspection end.
Preliminary Check
EKS0014V
SETTING CHANGE FUNCTION FOR AUTO LIGHT SYSTEM
●
Setting for each operation can be changed using CONSULT-II and a display unit.
INSPECTION FOR POWER SUPPLY AND GROUND CIRCUIT
1.
FUSE CHECK
Check if any of the following fuses in BCM are blown.
OK or NG
OK
>> GO TO 2.
NG
>> If the fuse is brown be sure to eliminate cause of incident before installing new fuse.
SKIA3782E
Unit
Power source
Terminal
Fuse No.
BCM
BAT power supply
105
3
ACC power supply
60
21
IGN power supply
68
1
HEADLAMP (FOR USA)
LT-21
C
D
E
F
G
H
I
J
L
M
A
B
LT
2.
POWER SUPPLY CIRCUIT CHECK
1.
Disconnect the BCM connector.
2.
Check voltage between BCM and ground.
OK or NG
OK
>> GO TO 3.
NG
>> Check harness for open or short between BCM and fuse.
3.
GROUND CIRCUIT CHECK
Check continuity between BCM harness connector M4 terminals 56,
113 and body ground.
OK or NG
OK
>> Inspection end.
NG
>> Repair or replace harness.
Unit
Terminals
(wire color)
Power
source
condition
Voltage
Connector
(+)
(–)
BCM
(M4)
105 (Y/L)
Body
ground
Battery
power
supply
Ignition
switch
OFF
Battery
voltage
68 (W/B)
IGN
power
supply
Ignition
switch
ON
Battery
voltage
60 (L/OR)
ACC
power
supply
Ignition
switch
ACC
Battery
voltage
SKIA3939E
Unit
Terminal
(wire color)
Signal
Ignition
switch
Continuity
Connec-
tor
(+)
(–)
BCM(M4)
56 (B)
Body
ground
Ground
Ignition
switch
OFF
Continuity
should exist
113(B)
Body
ground
Ground
Ignition
switch
OFF
Continuity
should exist
PIIA0170E
LT-22
HEADLAMP (FOR USA)
CONSULT-II Function for Auto Light System
EKS000VO
●
CONSULT-II has the display function for the work support, data monitor and active test for each part by
combining data receiving and sending via the communication line from the BCM.
CONSULT-II BASIC OPERATION PROCEDURE
1.
With the ignition switch OFF, connect “CONSULT-II” and “CON-
SULT-II CONVERTER” to the data link connector, then turn igni-
tion switch ON.
2.
Touch “START(NISSAN BASED VHCL)”.
3.
Touch “IVMS” on “SELECT SYSTEM” screen. If “IVMS” is not
indicated, go to
GI-38, "CONSULT-II Data Link Connector (DLC)
4.
Check the model specification, touch either “WITH SUNROOF”
or “WITHOUT SUNROOF”.
5.
Touch “OK”. If the selection is wrong, touch “CANCEL”.
IVMS diagnosis position
Diagnosis mode
Description
auto light system
Work support
Changes setting of each function.
Data monitor
Displays input data of the BCM and each LCU in real-time.
Active test
Operation of electrical loads can be checked by sending driving signal to them.
BCM part number
Displays BCM part No.
SHIA0179E
SKIA3098E
SKIA3783E
PIIA0184E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст