Infiniti F50. Manual — part 595
FRONT DOOR GLASS AND REGULATOR
GW-51
C
D
E
F
G
H
J
K
L
M
A
B
GW
FRONT DOOR GLASS AND REGULATOR
PFP:80300
Removal and Installation
EIS000JH
REMOVAL
1.
Remove the front door finisher. Refer to
EI-30, "Removal and Installation"
2.
Remove the door speaker. Refer to
AV-36, "Removal and Installation of Door Speaker"
3.
Remove the front door sash cover. Refer to
EI-30, "Removal and Installation"
4.
Pull the inside seal out of the inner panel.
5.
Operate the power window main switch to raise/lower the door
window until the glass mounting bolts can be seen.
6.
Remove the glass mounting bolts.
SIIA0285E
PIIA9439E
SIIA0264E
GW-52
FRONT DOOR GLASS AND REGULATOR
7.
While holding the door window, raise it at the rear end to pull the
glass out of the sash toward the outside of the door.
8.
Remove the mounting bolts, and remove the module assembly.
9.
Disconnect the harness connector for the module assembly, and
remove the harness clip from the back.
INSTALLATION
Install in the reverse order of removal.
INSPECTION AFTER REMOVAL
Check the regulator assembly for the following items. If a malfunc-
tion is detected, replace or body grease it.
●
Wire wear
●
Regulator deformation
●
Grease condition for each sliding part
The arrows in the figure show the application points of the body
grease.
DISASSEMBLY AND ASSEMBLY
Remove the power window motor and guide rail from the module
assembly.
SIIA0286J
SIIA0287E
SIIA0297J
SIIA0298E
FRONT DOOR GLASS AND REGULATOR
GW-53
C
D
E
F
G
H
J
K
L
M
A
B
GW
SETTING AFTER INSTALLATION
Setting of limit switch
If any of the following work has been done, set the limit switch (integrated in the motor).
●
Removal and installation of the regulator.
●
Removal and installation of the motor from the regulator.
●
Operate the regulators as a unit.
●
Removal and installation of the glass.
●
Removal and installation of the glass run.
Resetting
After installing each component to the vehicle, follow the steps below.
1.
Raise the glass to the top position.
2.
While pressing and holding the reset switch, lower the glass to
the bottom position.
3.
Release the reset switch, and check that the reset switch returns
to the original position, and then raise the glass to the top posi-
tion.
CAUTION:
Do not operate the glass automatically to raise the glass to
the top position.
FITTING INSPECTION
●
Check that the glass is securely fit into the glass run groove.
●
Lower the glass slightly [approx. 10 to 20 mm (0.39 to 0.79 in)] and check that the clearance to the sash is
parallel. If the clearance between the glass and sash is not parallel, loosen the regulator mounting bolts,
guide rail mounting bolts, and glass & guide rail mounting bolts to correct the glass position.
SIIA0347E
GW-54
REAR DOOR GLASS AND REGULATOR
REAR DOOR GLASS AND REGULATOR
PFP:82300
Removal and Installation
EIS000JI
REMOVAL
1.
Lower the glass to the bottom position.
2.
Remove the rear door outside molding. Refer to
EI-27, "Removal and Installation"
.
3.
Remove the rear door finisher. Refer to
EI-30, "Removal and Installation"
.
4.
Pull the inside seal out of the inner panel.
5.
Remove the mounting bolts, and remove the frame assembly.
SIIA0288E
PIIA9439E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст