Infiniti F50. Manual — part 815
SIDE CURTAIN AIR BAG MODULE
SRS-47
C
D
E
F
G
I
J
K
L
M
A
B
SRS
SIDE CURTAIN AIR BAG MODULE
PFP:985P0
Removal and Installation
EHS0008S
REMOVAL
CAUTION:
●
Before servicing SRS, turn the ignition switch off, disconnect both battery cables and wait at least
3 minutes.
●
Always work from the side of the side curtain air bag module.
1.
Remove rear pillar finisher. Refer to
EI-37, "Removal and Installation"
2.
Disconnect the side curtain air bag module connector.
3.
EI-49, "Removal and Installation"
4.
Remove side curtain air bag module fixing bolts, and remove the side curtain air bag module.
CAUTION:
●
Always place the side curtain air bag module with the caution label facing upward.
●
Do not attempt to disassemble side curtain air bag module.
●
Do not insert any foreign objects (screwdriver, etc.) into air
bag module connector.
●
Replace side curtain air bag module if it has been dropped
or sustained an impact.
●
Do not expose the air bag module to temperatures exceed-
ing 90
°
C (194
°
F).
●
Do not allow oil, grease or water to come in contact with the
side curtain air bag module.
INSTALLATION
To install, reverse the removal procedure sequence.
CAUTION:
●
Always work from the side of the side curtain air bag module.
●
After replacement of side curtain air bag module, perform self-diagnosis to check that no malfunc-
tion is detected. Refer to
.
SHIA0190E
SBF814E
SRS-48
CRASH ZONE SENSOR
CRASH ZONE SENSOR
PFP:98531
Removal and Installation
EHS0009M
REMOVAL
CAUTION:
●
Before servicing SRS, turn the ignition switch off, disconnect both battery cables and wait at least
3 minutes.
1.
Remove front grille. Refer to
EI-19, "Removal and Installation"
.
2.
Remove crash zone sensor connector.
3.
Remove crash zone sensor fixing nuts.
CAUTION:
●
Replace crash zone sensor if it has been dropped or sustained an impact.
●
Do not attempt to disassemble crash zone sensor.
INSTALLATION
To install, reverse the removal procedure sequence.
CAUTION:
●
Check crash zone sensor for proper installation.
●
After the work is complete, perform self-diagnosis to check that no malfunction is detected. Refer
to
SHIA0191E
SIDE AIR BAG (SATELLITE) SENSOR
SRS-49
C
D
E
F
G
I
J
K
L
M
A
B
SRS
SIDE AIR BAG (SATELLITE) SENSOR
PFP:98830
Removal and Installation
EHS0008U
REMOVAL
CAUTION:
●
Before servicing SRS, turn the ignition switch off, disconnect both battery cables and wait at least
3 minutes.
1.
Remove seat belt pre-tensioned. Refer to
and
SB-3, "Removal and Installation of Front Seat Belt"
2.
Remove side air bag (Satellite) sensor fixing nuts.
3.
Remove the side air bag (Satellite) sensor connector.
CAUTION:
●
Do not use old bolts, replace with new ones.
●
Check side air bag (Satellite) sensor to ensure they are free of deformities, dents, cracks or rust. If
it shows any visible signs of damage, replace it with new one.
●
Do not attempt to disassemble side air bag (Satellite) sensor.
●
Replace side air bag (Satellite) sensor if it has been dropped or sustained an impact.
●
When the front side air bag or side curtain air bag deploys, always replace it with a new one.
INSTALLATION
To install, reverse the removal procedure sequence.
CAUTION:
●
Check side air bag (Satellite) sensor for proper installation.
●
After replacement of side air bag (Satellite) sensor, perform self-diagnosis to check that no mal-
function is detected. Refer to
.
SHIA0194E
SRS-50
FRONT SEAT BELT PRE-TENSIONER
FRONT SEAT BELT PRE-TENSIONER
PFP:86884
Removal and Installation
EHS000O5
To removal and installation procedures, refer to
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст