Infiniti F50. Manual — part 821
ELECTRICALLY CONTROLLED POWER STEERING SYSTEM
STC-9
[EPS]
C
D
E
F
H
I
J
K
L
M
A
B
STC
10.
POWER STEERING CONTROL UNIT GROUND INSPECTION
Check for continuity between the power steering control unit terminal
2 (B) and body ground.
Is the result OK?
OK
>> GO TO 11.
NG
>> Repair or replace harness.
11.
ENGINE REVOLUTION SIGNAL INSPECTION
Check power steering control unit terminal 5 (W/G),. Refer to
"Control Unit Inspection Table"
.
Is the result OK?
OK
>> GO TO 1.
NG
>> Check harness between ECM and control unit or ECM.
Repair or replace harness if necessary.
Control Unit Inspection Table
EGS0007Z
The standard values (voltage), measured with an analog tester in contact with control unit terminal, are shown
below:
2 (B) - Body ground
: Continuity should exist
SGIA0051E
SGIA0052E
Inspection terminal
Condition
Application
Standard
Power steering control
unit
1
Ignition switch ON
Power
Battery voltage (approx. 12V)
2
Ground
0V
3
Vehicle speed signal
When the speed is very low, the voltage fluctuates
between approximately 0V and approximately 5V
or higher.
5
Engine running
Engine revolution signal
Measure the tachometer drive signal.
Refer to
EC-99, "ECM Harness Connector Termi-
7
Solenoid valve
Normal
0 km/h ((0 MPH)
: Approx. 4.4 - 6.6V
100 km/h (62 MPH): Approx. 2.4 - 3.6V
When the fail-safe function is activated:
0 - 1,500 rpm
: Approx. 4.4 - 6.6V
1,500 - 3,000 rpm : Approx. 3.5V
3,000 rpm or more: Approx. 2.1V
STC-10
[EPS]
ELECTRICALLY CONTROLLED POWER STEERING SYSTEM
WT-1
ROAD WHEELS & TIRES
E SUSPENSION
CONTENTS
C
D
F
G
H
I
J
K
L
M
SECTION
A
B
WT
ROAD WHEELS & TIRES
PREPARATION . . . . . . . . . . . . . . ... 2
Special Service Tool . . . . . . . . . . . . . 2
Commercial Service Tools . . . . . . . . . . 2
NOISE, VIBRATION AND HARSHNESS (NVH)
TROUBLESHOOTING . . . . . . . . . . . . 3
NVH Troubleshooting Chart . . . . . . . . . . 3
ROAD WHEEL . . . . . . . . . . . . . . . 4
Inspection . . . . . . . . . . . . . . . . . 4
ALUMINUM WHEEL . . . . . . . . . . . . 4
STEEL WHEEL . . . . . . . . . . . . . . 4
ROAD WHEEL TIRE ASSEMBLY . . . . . . . .. 5
Balancing Wheels (Bonding Weight Type) . . . ... 5
REMOVAL . . . . . . . . . . . . . . . . 5
WHEEL BALANCE ADJUSTMENT . . . . . .. 5
Rotation . . . . . . . . . . . . . . . . . 6
LOW TIRE PRESSURE WARNING SYSTEM . . . 7
System Components . . . . . . . . . . . . 7
System Description . . . . . . . . . . . . .. 7
VEHICLE INFORMATION DISPLAY . . . . . . 8
TROUBLE DIAGNOSES . . . . . . . . . . . 9
Wiring Diagram . . . . . . . . . . . . . . 9
ID Registration Procedure . . . . . . . . . .. 13
Transmitter Wake Up Operation . . . . . . . . 14
WITH TRANSMITTER ACTIVATION TOOL . . 14
Self-Diagnosis . . . . . . . . . . . . . . 15
How to Perform Trouble Diagnosis for Quick and
Accurate Repair . . . . . . . . . . . . . . 17
INTRODUCTION . . . . . . . . . . . . . 17
WORK FLOW . . . . . . . . . . . . . .. 17
Preliminary Check . . . . . . . . . . . . .. 18
Malfunction Code/Symptom Chart . . . . . . .. 19
TROUBLE DIAGNOSIS FOR SELF-DIAGNOSTIC
ITEMS . . . . . . . . . . . . . . . . . . 20
Inspection 1: Transmitter or Low Tire Pressure
Warning Control Unit . . . . . . . . . . . .. 20
MALFUNCTION CODE NO. 21, 22, 23 OR 24 ... 20
Inspection 2: Transmitter - 1 . . . . . . . . ... 20
MALFUNCTION CODE NO. 31, 32, 33, 34, 41,
42, 43, 44, 45, 46, 47 OR 48 . . . . . . . ... 20
Inspection 3: Transmitter - 2 . . . . . . . . ... 21
MALFUNCTION CODE NO. 35, 36, 37 OR 38 ... 21
Inspection 4: Low Tire Pressure Warning Control
Unit . . . . . . . . . . . . . . . . . . . 21
MALFUNCTION CODE NO. 51 . . . . . . ... 21
TROUBLE DIAGNOSIS FOR SYMPTOMS . . . .. 22
REMOVAL AND INSTALLATION . . . . . . . . 26
Transmitter . . . . . . . . . . . . . . . . 26
REMOVAL . . . . . . . . . . . . . . ... 26
INSTALLATION . . . . . . . . . . . . ... 26
SERVICE DATA . . . . . . . . . . . . . . 28
Road Wheel . . . . . . . . . . . . . . . 28
Tire . . . . . . . . . . . . . . . . . . . 28
WT-2
PREPARATION
PREPARATION
PFP:00002
Special Service Tool
EES000CZ
The actual shapes of Kent-Moore tools may differ from those of special service tools illustrated here.
Commercial Service Tools
EES000N6
Tool number
(Kent-Moore No.)
Tool name
Description
(J45295)
Transmitter activation tool
ID registration
SEIA0051E
Tool name
Description
Power tool
Removing wheel nuts
PBIC0190E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст