Infiniti F50. Manual — part 297
COMPASS
DI-31
C
D
E
F
G
H
I
J
L
M
A
B
DI
Wiring Diagram – COMPAS –
EKS006D5
TKWM0293E
DI-32
COMPASS
Removal and Installation of Compass
EKS006TN
Refer to
GW-58, "Removal and Installation"
.
WARNING LAMPS
DI-33
C
D
E
F
G
H
I
J
L
M
A
B
DI
WARNING LAMPS
PFP:24814
System Description
EKS0010H
OUTLINE
Power is supplied at all times
●
through 10A fuse [No. 6, located in the fuse block (J/B) No. 1]
●
to combination meter terminal 57.
With ignition switch in the ON or START position, power is supplied
●
through 10A fuse [No. 9, located in the fuse block (J/B) No. 1]
●
to combination meter terminal 59.
Ground is supplied
●
to combination meter terminal 60
●
through grounds M24 and M114, and
●
to seat belt buckle switch terminal 15A
●
through grounds B17 and B57, and
●
to brake fluid level switch terminal 2
●
through grounds E24 and E44, and
●
to washer level switch terminal 2
●
through grounds E42 and E62.
AIR BAG WARNING LAMP
During probe out or when an air bag malfunction occurs, the ground path is interrupted
●
from the air bag diagnosis sensor unit terminal 15
●
to combination meter terminal 56.
Ground is supplied
●
through combination meter terminal 61
When power and ground are supplied, the air bag warning lamp (LEDs) illuminates.
For further information, refer to
DOOR WARNING LAMP
Door waning lamp is controlled by BCM.
When one of the doors is opened, ground is supplied to the BCM terminals 33, 37,142 and 143.
And then ground is supplied
●
to combination meter terminal 49
●
from BCM terminal 111
When power and ground are supplied, the door warning lamp illuminates.
ACTIVE DAMPER INDICATOR LAMP (SPORT)
When an active damper suspension system malfunction occurs, or “SPORT” mode is selected by active
damper suspension select switch, ground is supplied
●
to combination meter terminal 53
●
from active damper suspension control unit terminal 16
When power and ground are supplied, the active damper indicator lamp (SPORT) blinks or illuminates.
For further information.
LOW OIL PRESSURE WARNING LAMP
Low oil pressure causes oil pressure switch terminal 1 to provide ground to combination meter terminal 12.
When power and ground are supplied, the low oil pressure warning lamp illuminates.
CHARGE WARNING LAMP
During prove out or when an alternator malfunction occurs, ground is supplied
●
to combination meter terminal 13
●
from alternator terminal 3
When power and ground are supplied, the charge warning lamp and brake lamp illuminate.
DI-34
WARNING LAMPS
LOW WASHER LEVEL WARNING LAMP
When the washer fluid level is low, ground is supplied
●
to combination meter terminal 26
●
from washer level switch terminal 1.
When power and ground are supplied, the signal is sent
●
from combination meter terminal 6 and 7
●
through AV and NAVI control unit terminal 32 and 33 or AV control unit terminals 35 and 34
●
to display.
Then warning lamp message appears display.
A/T OIL TEMPERATURE WARNING LAMP
When an A/T system malfunction occurs, signal sent
●
to combination meter terminals 15 and 16
●
from TCM (transmission control module) with CAN communication line.
When signal is received, the AT oil temperature warning lamp blinks or illuminates.
For further information, refer to
AT-238, "A/T CHECK Indicator Lamp does not come on"
.
LOW-FUEL LEVEL WARNING LAMP
The amount of fuel in the fuel tank is determined by the fuel level sensor in the fuel tank. Fuel level signal is
sent
●
from fuel level sensor unit terminal 5
●
to combination meter terminal 30
●
through fuel level sensor unit terminal 6
●
to combination meter terminal 29.
The fuel level sensor will illuminate the low-fuel level warning lamp when the fuel level is low.
When power and ground are supplied, the low-fuel level warning lamp illuminates.
ABS WARNING LAMP
When an ABS malfunction occurs, ground is supplied
●
to combination meter terminal 52
●
from VDC/TCS/ABS control unit terminal 30.
When power and ground is supplied, the ABS warning lamp illuminates.
For further information, refer to
BRC-64, "Symptom 5 Pedal Vibration and Noise"
.
VDC OFF INDICATOR LAMP
When VDC off switch is in OFF position, or an VDC/TCS/ABS malfunction occurs, ground is supplied
●
to combination meter terminal 67
●
from VDC/TCS/ABS control unit terminal 31.
When power and ground are supplied, the VDC off warning lamp illuminates.
For further information, refer to
BRC-66, "Symptom 6 VDC OFF Indicator Lamp Does Not Illuminate."
SLIP INDICATOR LAMP
When VDC is in operation, or a VDC malfunction occurs, ground is supplied
●
to combination meter terminal 66
●
from VDC/TCS/ABS control unit terminal 83.
When power and ground are supplied, the slip warning lamp illuminates.
For further information, refer to
BRC-66, "Symptom 7 SLIP Indicator Lamp Does Not Illuminate."
.
SEAT BELT WARNING LAMP
When the driver's seat belt is unfastened, ground is supplied
●
to combination meter terminal 50
●
from seat belt buckle switch terminal 41.
When power and ground are supplied, the seat belt warning lamp illuminates.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст