Infiniti F50. Manual — part 239
IVIS (INFINITI VEHICLE IMMOBILIZER SYSTEM-NATS)
BL-203
C
D
E
F
G
H
J
K
L
M
A
B
BL
TIWM0203E
BL-204
IVIS (INFINITI VEHICLE IMMOBILIZER SYSTEM-NATS)
TIWM0204E
IVIS (INFINITI VEHICLE IMMOBILIZER SYSTEM-NATS)
BL-205
C
D
E
F
G
H
J
K
L
M
A
B
BL
Terminals and Reference Value for Steering Lock Control Unit
EIS003R3
Terminals and Reference Value for NATS IMMU
EIS003R4
TERMINAL
WIRE
COLOR
ITEM
CONDITION
VOLTAGE
1
Y/G
Battery power supply
—
Battery voltage
2
PU/W
Key switch
Key inserted (ON)
→
Key removed from
IGN key cylinder (OFF)
Battery voltage
→
0V
3
L
NATS IMMU
Key inserted (key switch OFF
→
ON)
Just after inserting electronic key to
key cylinder: Point of tester should
move
4
B
Ground
—
0V
TERMINAL
WIRE
COLOR
ITEM
CONDITION
VOLTAGE
1
W
Battery power supply
—
battery voltage
2
PU/W
Key switch
Key inserted (ON)
→
Key removed from
IGN key cylinder (OFF)
Battery voltage
→
0V
3
W/B
Ignition switch
Ignition switch ON or START position
Battery voltage
5
R
NATS antenna amp.
key inserted (key switch OFF
→
ON)
0V
→
Approx. 5V (for 3 seconds)
6
Y
NATS antenna amp.
Key inserted (key switch OFF
→
ON)
Just after inserting electronic key to
key cylinder: Point of tester should
move
7
Y/G
NATS antenna amp.
Key inserted (key switch OFF
→
ON)
Just after inserting electronic key to
key cylinder: Point of tester should
move
8
B/R
NATS antenna amp.
—
0V
9
B/W
Ground
—
0V
10
L
Steering lock control unit
Key inserted (key switch OFF
→
ON)
Just after inserting electronic key to
key cylinder: Point of tester should
move
11
G/W
ECM
—
—
15
G
Security indicator lamp
Goes OFF
→
illuminates (every 2.4 sec-
onds)
Battery voltage
→
0V
BL-206
IVIS (INFINITI VEHICLE IMMOBILIZER SYSTEM-NATS)
CONSULT-II
EIS0012D
CONSULT-II INSPECTION PROCEDURE
1.
Turn ignition switch OFF.
2.
Insert IVIS (NATS) program card into CONSULT-II.
3.
Connect CONSULT-II and “CONSULT-II CONVERTER” to data
link connector.
4.
Turn ignition switch ON.
5.
Touch “START”.
6.
Perform each diagnostic test mode according to each service
procedure.
For further information, see the CONSULT-II Operation Manual,
IVIS/NVIS.
CONSULT-II DIAGNOSTIC TEST MODE FUNCTION
NOTE:
When any initialization is performed, all ID numbers previously registered will be erased and all IVIS (NATS)
electronic keys must be registered again. The engine cannot be started with an unregistered key. The system
will show “DIFFERENCE OF KEY” or “LOCK MODE” as a self-diagnostic result on the CONSULT-II screen.
Program card
: NATS (AEN02B)
PBIB0196E
PBR455D
SEL150X
CONSULT- II DIAGNOSTIC TEST MODE
Description
C/U INITIALIZATION
When replacing any of the following three components, C/U initialization is necessary.
[IVIS (NATS) electronic key/ NATS IMMU/ ECM]
SELF- DIAGNOSTIC RESULTS
Detected items (screen terms) are as shown in the chart.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст