Infiniti F50. Manual — part 391
DTC P0127 IAT SENSOR
EC-205
C
D
E
F
G
H
I
J
K
L
M
A
EC
DTC P0127 IAT SENSOR
PFP:22630
Component Description
EBS00LYM
The intake air temperature sensor is built into mass air flow sensor.
The sensor detects intake air temperature and transmits a signal to
the ECM.
The temperature sensing unit uses a thermistor which is sensitive to
the change in temperature. Electrical resistance of the thermistor
decreases in response to the temperature rise.
<Reference data>
*: These data are reference values and are measured between ECM terminal 99
(Intake air temperature sensor) and ground.
CAUTION:
Do not use ECM ground terminals when measuring input/output
voltage. Doing so may result in damage to the ECM's transistor. Use a ground other than ECM termi-
nals, such as the ground.
On Board Diagnosis Logic
EBS00LYN
SEC266C
Intake air
temperature
°
C (
°
F)
Voltage*
V
Resistance
k
Ω
−
10 (14)
4.43
7.9 - 9.3
25 (77)
3.32
1.9 - 2.1
80 (176)
1.23
0.31 - 0.37
SEF012P
DTC No.
Trouble diagnosis name
DTC detecting condition
Possible cause
P0127
0127
Intake air temperature
too high
Rationally incorrect voltage from the sensor is
sent to ECM, compared with the voltage signal
from engine coolant temperature sensor.
●
Harness or connectors
(The sensor circuit is open or shorted)
●
Intake air temperature sensor
EC-206
DTC P0127 IAT SENSOR
DTC Confirmation Procedure
EBS00LYO
NOTE:
If “DTC Confirmation Procedure” has been previously conducted, always turn ignition switch “OFF” and wait at
least 10 seconds before conducting the next test.
CAUTION:
Always drive vehicle at a safe speed.
TESTING CONDITION:
This test may be conducted with the drive wheels lifted in the shop or by driving the vehicle. If a road
test is expected to be easier, it is unnecessary to lift the vehicle.
WITH CONSULT-II
1.
Wait until engine coolant temperature is less than 90
°
C (194
°
F)
a.
Turn ignition switch “ON”.
b.
Select “DATA MONITOR” mode with CONSULT-II.
c.
Check the engine coolant temperature.
d.
If the engine coolant temperature is not less than 90
°
C (194
°
F),
turn ignition switch “OFF” and cool down engine.
●
Perform the following steps before engine coolant tempera-
ture reaches 90
°
C (194
°
F).
2.
Turn ignition switch “ON”.
3.
Select “DATA MONITOR” mode with CONSULT-II.
4.
Start engine.
5.
Hold vehicle speed at more than 71 km/h (44 MPH) for 100 con-
secutive seconds.
6.
If 1st trip DTC is detected, go to
EC-208, "Diagnostic Procedure"
.
WITH GST
Follow the procedure “WITH CONSULT-II” above.
PBIB1917E
DTC P0127 IAT SENSOR
EC-207
C
D
E
F
G
H
I
J
K
L
M
A
EC
Wiring Diagram
EBS00LYP
TBWM0008E
EC-208
DTC P0127 IAT SENSOR
Diagnostic Procedure
EBS00LYQ
1.
CHECK INTAKE AIR TEMPERATURE SENSOR POWER SUPPLY CIRCUIT
1.
Turn ignition switch “OFF”.
2.
Disconnect mass air flow sensor (intake air temperature sensor
is built-into) harness connector.
3.
Turn ignition switch “ON”.
4.
Check voltage between mass air flow sensor terminal 5 and
ground.
OK or NG
OK
>> GO TO 2.
NG
>> Repair harness or connectors.
2.
CHECK INTAKE AIR TEMPERATURE SENSOR GROUND CIRCUIT FOR OPEN AND SHORT
1.
Turn ignition switch “OFF”.
2.
Disconnect ECM.
3.
Check harness continuity between mass air flow sensor terminal 3 and ECM terminal 109.
Refer to Wiring Diagram.
4.
Also check harness for short to ground and short to power.
OK or NG
OK
>> GO TO 3.
NG
>> Repair open circuit or short to ground or short to power in harness or connectors.
3.
CHECK INTAKE AIR TEMPERATURE SENSOR
Refer to
EC-209, "Component Inspection"
OK or NG
OK
>> GO TO 4.
NG
>> Replace mass air flow sensor (with intake air temperature sensor).
4.
CHECK INTERMITTENT INCIDENT
Refer to
EC-132, "TROUBLE DIAGNOSIS FOR INTERMITTENT INCIDENT"
.
>> INSPECTION END
PBIB0012E
Voltage: Approximately 5 V
PBIB0066E
Continuity should exist.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст