Infiniti F50. Manual — part 541
CAMSHAFT
EM-51
C
D
E
F
G
H
I
J
K
L
M
A
EM
Camshaft Sprocket Runout
1.
Install camshaft in cylinder head.
2.
Install camshaft sprocket to camshaft.
3.
Measure camshaft sprocket runout.
4.
If it exceeds the specifications, replace camshaft sprocket.
Valve Lifter and Adjusting Shim
Check if surface of valve lifter and adjusting shim has any wear or
cracks.
Valve Lifter Clearance
Outer Diameter of Valve Lifter
Measure outer diameter of valve lifter.
Valve Lifter Hole Diameter
Using inside micrometer, measure diameter of valve lifter hole of cyl-
inder head.
Calculation of Valve Lifter Clearance
(Valve lifter clearance) = (hole diameter of valve lifter) – (outer diam-
eter of valve lifter)
●
When out of specified range, referring to each specification of outer and inner diameter, replace either or
both valve lifter and cylinder head.
Runout
: Less than 0.15 mm (0.0059 in)
PBIC0930E
PBIC0231E
Standard: 33.965 - 33.975 mm (1.3372 - 1.3376 in)
SEM961E
Standard:
34.000 - 34.016 mm (1.3386 - 1.3392 in)
Standard:
0.025 - 0.051 mm (0.0010 - 0.0020 in)
PBIC0043E
EM-52
CAMSHAFT
Valve Clearance
EBS002MQ
INSPECTION
Perform inspection as follows after removal, installation or replacement of camshaft or valve-related parts, or if
there is unusual engine conditions due to changes in valve clearance over time (starting, idling, and/or noise).
1.
Warm up engine. Then, stop it.
2.
Remove engine cover and engine room covers (RH and LH) with power tool and air duct (inlet). Refer to
EM-11, "Removal and Installation"
3.
Remove RH and LH rocker covers with power tool. Refer to
EM-33, "Removal and Installation"
.
4.
Turn crankshaft pulley in normal direction (clockwise when
viewed from FRONT) to align TDC identification notch (without
paint mark) with timing indicator.
5.
At this time, check that the both intake and exhaust cam noses
of No. 1 cylinder (top front on left bank) face outside.
●
If they do not face outside, turn crankshaft pulley once more.
6.
By referring to the figure, measure valve clearances at locations
marked X as shown in the table below (locations indicated with
black arrow in figure) with a thickness gauge.
NOTE:
Firing order 1-8-7-3-6-5-4-2
●
No.1 cylinder compression TDC
PBIC0044E
KBIA0400J
Measuring position (RH bank)
No.2 CYL
No.4 CYL
No.6 CYL
No. 8 CYL
No. 1 cylinder at TDC
EXH
×
INT
×
×
Measuring position (LH bank)
No.1 CYL
No. 3 CYL
No. 5 CYL
No. 7 CYL
No. 1 cylinder at TDC
INT
×
×
EXH
×
×
PBIC0823E
CAMSHAFT
EM-53
C
D
E
F
G
H
I
J
K
L
M
A
EM
●
Use a fine thickness gauge.
*Approximately 20
°
C (68
°
F)
CAUTION:
If inspection was carried out with cold engine, check that
values with fully warmed up engine are still within speci-
fications.
7.
Turn crankshaft pulley clockwise by 270
°
from the position of No. 1 cylinder compression TDC to obtain
No. 3 cylinder compression TDC.
8.
By referring to the figure, measure valve clearances at locations
marked X as shown in the table below (locations indicated with
white arrow in figure)
●
No.3 cylinder compression TDC
9.
Turn crankshaft pulley clockwise by 90
°
from the position of No.
3 cylinder compression TDC (clockwise by 360
°
from the posi-
tion of No. 1 cylinder compression TDC) to measure intake and
exhaust valve clearances of No. 6 cylinder and exhaust valve
clearance of No.2 cylinder.
10. If out of specifications, adjust as follows:
Valve clearance standard:
Hot
Intake
: 0.32 - 0.40 mm (0.013 - 0.016 in)
Exhaust
: 0.33 - 0.41 mm (0.013 - 0.016 in)
Cold*
Intake
: 0.26 - 0.34 mm (0.010 - 0.013 in)
Exhaust
: 0.29 - 0.37 mm (0.011 - 0.015 in)
PBIC0046E
Measuring position (RH bank)
No.2 CYL
No.4 CYL
No.6 CYL
No. 8 CYL
No. 3 cylinder at TDC
EXH
×
INT
×
Measuring position (LH bank)
No.1 CYL
No. 3 CYL
No. 5 CYL
No. 7 CYL
No. 3 cylinder at TDC
INT
×
×
EXH
×
×
PBIC0823E
PBIC0824E
EM-54
CAMSHAFT
ADJUSTMENT
Adjust valve clearance while engine is cold.
1.
Turn crankshaft, to position cam lobe on camshaft of valve that
must be adjusted upward.
2.
Thoroughly wipe off engine oil around adjusting shim using a
rag.
3.
Using a extra-fine screwdriver, turn the round hole of the adjust-
ing shim in the direction of the arrow.
4.
Place Tool (A) around camshaft as shown in figure.
●
Before placing Tool (A), rotate cam lobe toward center of cyl-
inder head (See (1) in figure.) to simplify shim removal later.
CAUTION:
Be careful not to damage cam surface with Tool (A).
5.
Rotate Tool (A) (See (2) in figure.) so that valve lifter is pushed
down.
6.
Place Tool (B) between camshaft and the edge of the valve lifter
to retain valve lifter.
CAUTION:
●
Tool (B) must be placed as close to camshaft bracket as
possible.
●
Be careful not to damage cam surface with Tool (B).
7.
Remove Tool (A).
8.
Blow air into the hole to separate adjusting shim from valve lifter.
CAUTION:
When blowing, use goggles to protect your eye.
PBIC0047E
SBIA0408E
SEM870E
SEM871E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст