Infiniti F50. Manual — part 375
DTC U1000, U1001 CAN COMMUNICATION LINE
EC-141
C
D
E
F
G
H
I
J
K
L
M
A
EC
DTC U1000, U1001 CAN COMMUNICATION LINE
PFP:23710
Description
EBS00LWJ
CAN (Controller Area Network) is a serial communication line for real time application. It is an on-vehicle mul-
tiplex communication line with high data communication speed and excellent error detection ability. Many elec-
tronic control units are equipped onto a vehicle, and each control unit shares information and links with other
control units during operation (not independent). In CAN communication, control units are connected with 2
communication lines (CAN H line, CAN L line) allowing a high rate of information transmission with less wiring.
Each control unit transmits/receives data but selectively reads required data only.
On Board Diagnosis Logic
EBS00LWK
*1: This self-diagnosis has the one trip detection logic.
*2: The MIL will not light up for this diagnosis.
DTC Confirmation Procedure
EBS00LWL
1.
Turn ignition switch “ON” and wait at least 3 seconds.
2.
Select “DATA MONITOR” mode with CONSULT-II.
3.
If 1st trip DTC is detected, go to
EC-143, "Diagnostic Procedure"
DTC No.
Trouble diagnosis name
DTC detecting condition
Possible cause
U1000*
1
1000*
1
CAN communication line
●
ECM cannot communicate to other control units.
●
ECM cannot communicate for more than the
specified time.
●
Harness or connectors
(CAN communication line is open or
shorted)
U1001*
2
1001*
2
EC-142
DTC U1000, U1001 CAN COMMUNICATION LINE
Wiring Diagram
EBS00LWM
TBWM0055E
DTC U1000, U1001 CAN COMMUNICATION LINE
EC-143
C
D
E
F
G
H
I
J
K
L
M
A
EC
Diagnostic Procedure
EBS00LWN
1.
INSPECTION START
1.
Turn ignition switch “ON”.
2.
Select “CAN DIAG SUPPORT MNTR” in “DATA MONITOR” mode with CONSULT-II.
3.
Print out the CONSULT-II screen.
Models without ICC
Models with ICC
>> Go to
LAN-24, "CAN SYSTEM (FOR VDC MODELS)"
PBIB1145E
PBIB1146E
EC-144
DTC P0011, P0021 IVT CONTROL
DTC P0011, P0021 IVT CONTROL
PFP:23796
Description
EBS00LWO
If DTC P1110 or P1135 is displayed with DTC P1111, P1136, P1140 or P1145, first perform the trouble
diagnosis for
EC-424, "DTC P1111, P1136 IVT CONTROL SOLENOID VALVE"
or
P1145 IVT CONTROL POSITION SENSOR"
.
SYSTEM DESCRIPTION
*: This signal is sent to the ECM through CAN communication line.
This mechanism hydraulically controls cam phases continuously with the fixed operating angle of the intake
valve.
The ECM receives signals such as crankshaft position, camshaft position, engine speed, and engine coolant
temperature. Then, the ECM sends ON/OFF pulse duty signals to the intake valve timing (IVT) control sole-
noid valve depending on driving status. This makes it possible to control the shut/open timing of the intake
valve to increase engine torque in low/mid speed range and output in high-speed range.
COMPONENT INSPECTION
Intake Valve Timing Control Solenoid Valve
Intake Valve Timing (IVT) control solenoid valve is activated by ON/
OFF pulse duty (ratio) signals from the ECM.
The IVT control solenoid valve changes the oil amount and direction
of flow through intake valve timing control unit or stops oil flow.
The longer pulse width advances valve angle.
The shorter pulse width retards valve angle.
When ON and OFF pulse widths become equal, the solenoid valve
stops oil pressure flow to fix the intake valve angle at the control
position.
Sensor
Input signal to ECM function
ECM
Actuator
Crankshaft position sensor (POS)
Camshaft position sensor (PHASE)
Engine speed
Intake valve
timing control
Intake valve timing control
solenoid valve
Intake valve timing control position sensor
Intake valve timing signal
Engine coolant temperature sensor
Engine coolant temperature
Wheel sensor*
Vehicle speed
PBIB1102E
PBIB1842E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст