Infiniti F50. Manual — part 96
TROUBLE DIAGNOSIS FOR SYMPTOMS
AT-269
D
E
F
G
H
I
J
K
L
M
A
B
AT
6.
PERFORM TCM INSPECTION
1.
Perform TCM input/output signal inspection.
2.
If NG, recheck TCM pin terminals for damage or loose connection with harness connector.
OK or NG
OK
>> INSPECTION END
NG
>> Repair or replace damaged parts.
7.
DETECT MALFUNCTIONING ITEM
●
Check the malfunction items. If any items are damaged, repair or replace damaged parts. Refer to
OK or NG
OK
>> GO TO 5.
NG
>> Repair or replace damaged parts.
AT-270
TROUBLE DIAGNOSIS FOR SYMPTOMS
Cannot Be Changed to Manual Mode
ECS0089N
SYMPTOM:
Does not change to manual mode when manual shift gate is used.
DIAGNOSTIC PROCEDURE
1.
MANUAL MODE SWITCH
Check the manual mode switch. Refer to
AT-215, "DTC P1815 MANUAL MODE SWITCH"
OK or NG
OK
>> GO TO 2.
NG
>> Repair or replace damaged parts.
2.
CHECK SELF-DIAGNOSTIC RESULTS
Execute self-diagnosis.
Do the self-diagnostic results indicate turbine revolution sensor?
YES
>> Check the malfunctioning system. Refer to
AT-152, "DTC P1716 TURBINE REVOLUTION SEN-
NO
>> INSPECTION END
TROUBLE DIAGNOSIS FOR SYMPTOMS
AT-271
D
E
F
G
H
I
J
K
L
M
A
B
AT
A/T Does Not Shift: 5th gear
→
4th gear
ECS0089O
SYMPTOM:
When shifted from 5M to 4M position in manual mode, does not downshift from 5th to 4th gear.
DIAGNOSTIC PROCEDURE
1.
CHECK SELF-DIAGNOSTIC RESULTS
Execute self-diagnosis.
Do the self-diagnostic results indicate PNP switch, ATF pressure switch 1?
YES
>> Check the malfunctioning system. Refer to
AT-105, "DTC P0705 PARK/NEUTRAL POSITION
AT-219, "DTC P1841 ATF PRESSURE SWITCH 1"
NO
>> GO TO 2.
2.
CHECK A/T FLUID LEVEL
Check A/T fluid level again. Refer to
OK or NG
OK
>> GO TO 3.
NG
>> Refill ATF.
3.
CHECK CONTROL LINKAGE
Check the control linkage.
●
Refer to
AT-282, "Checking of A/T Position"
OK or NG
OK
>> GO TO 4.
NG
>> Adjust control linkage. Refer to
4.
MANUAL MODE SWITCH
Check the manual mode switch. Refer to
AT-215, "DTC P1815 MANUAL MODE SWITCH"
.
OK or NG
OK
>> GO TO 5.
NG
>> Repair or replace damaged parts.
SAT638A
SCIA1612E
AT-272
TROUBLE DIAGNOSIS FOR SYMPTOMS
5.
CHECK A/T FLUID CONDITION
1.
Remove oil pan. Refer to
AT-289, "Control Valve Assembly"
2.
Check A/T fluid condition.
OK or NG
OK
>> GO TO 6.
NG
>> GO TO 9.
6.
DETECT MALFUNCTIONING ITEM
●
Check the malfunction items. If any items are damaged, repair or replace damaged parts. Refer to
OK or NG
OK
>> GO TO 7.
NG
>> Repair or replace damaged parts.
7.
CHECK SYMPTOM
Check again.
OK or NG
OK
>> INSPECTION END
NG
>> GO TO 8.
8.
PERFORM TCM INSPECTION
1.
Perform TCM input/output signal inspection.
2.
If NG, recheck TCM pin terminals for damage or loose connection with harness connector.
OK or NG
OK
>> INSPECTION END
NG
>> Repair or replace damaged parts.
9.
DETECT MALFUNCTIONING ITEM
●
Check the malfunction items. If any items are damaged, repair or replace damaged parts. Refer to
OK or NG
OK
>> GO TO 7.
NG
>> Repair or replace damaged parts.
SAT171B
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст