Infiniti F50. Manual — part 762
AUTOMATIC DRIVE POSITIONER
SE-39
C
D
E
F
G
H
J
K
L
M
A
B
SE
CONSULT-II Function
EIS0043I
CONSULT–II executes the following functions by combining data received and transmits command transmis-
sion via the communication line from the BCM. IVMS communication inspection, work support by part, self-
diagnosis, data monitor, and active test display.
*: For setting seat and steering functions only.
CONSULT-II BASIC OPERATION PROCEDURE
1.
Turn ignition switch “OFF”.
2.
Connect “CONSULT-II” and CONSULT-II CONVERTER to data
link connector.
3.
Turn ignition switch “ON”.
4.
Touch “START(NISSAN BASED VHCL)”.
5.
Touch “IVMS”on the “SELECT SYSTEM” screen.
If “IVMS” is not indicated,
GI-38, "CONSULT-II Data Link Con-
IVMS diagnosis
items
Inspection item, self-
diagnosis mode
Content
IVMS –
COMM CHECK
IVMS–
COMM DIAGNOSIS
Diagnoses a communication malfunction, inactive communication, and sleep
malfunction in the communication line between the BCM and each LCU.
WAKE–
UP DIAGNOSIS
Diagnoses the wake-up signals output from each LCU.
AUTO DRIVE
POSITIONER
WORK SUPPORT*
Changes the setting for each function.
SELF–
DIG RESULTS
Perform the self-diagnosis.
DATA MONITOR
Displays the input data of the BCM and each LCU on real-time basis.
ACTIVE TEST
Gives a drive signal to a load to check the operation.
BCM PART NUMBER
Displays BCM part No.
PBIB1069E
MBIB0233E
PIIA0183E
SE-40
AUTOMATIC DRIVE POSITIONER
6.
Check the model specification, and touch either “WITH SUN-
ROOF” or “WITHOUT SUNROOF” on the “SELECT SYS
COND” screen.
7.
Touch “OK”. If the selection is wrong, touch “CANCEL”.
8.
Select the desired part to be diagnosed on the “SELECT TEST
ITEM” screen.
IVMS COMMUNICATION INSPECTION.
IVMS contains the IVMS communication diagnosis and wake-up diagnosis.
IVMS Communication Diagnosis
●
The function also stores the communication malfunction records and inactive communication records, and
displays the data on the CONSULT–II screen. (malfunction record diagnosis.)
NOTE:
Sleep is a power saving function when a vehicle is stationary (all BCM related electrical equipment: OFF,
and the timer: OFF).
*: Malfunction item record
Operation Procedure
1.
Touch “IVMS-COMM CHECK” on “SELECT TEST ITEM”.
2.
Touch “IVMS-COMM DIAGNOSIS” on the “SELECT DIAG ITEM” screen.
3.
Touch “START” on the “IVMS-COMM DIAGNOSIS” screen to start the diagnosis.
4.
After the diagnosis is completed, the malfunctioning system name is displayed.
5.
When the malfunctioning items are displayed, touch “PRINT” to keep the records.
6.
Touch “ERASE”.
7.
Carry out the communication inspection again to check that any malfunctioning item is displayed.
8.
Check the displayed items.
Wake-up Diagnosis.
The wake-up diagnosis is carried out when the BCM detects the wake-up signal from each local control unit
(LCU). When the switch shown on the screen is operated as instructed, each local control unit (LCU) outputs
the wake-up signal. If the BCM cannot detect the wake-up signal, it is judged malfunctioning. The malfunction-
ing local control unit (LCU) is displayed on the screen.
Operation Procedure
1.
Touch “IVMS-COMM CHECK” on the “SELECT TEST ITEM” screen.
2.
Touch “WAKE-UP DIAGNOSIS” on the “SELECT DIAG ITEM” screen.
3.
Touch “START” on the “WAKE-UP DIAGNOSIS” screen to start the diagnosis.
PIIA0184E
Malfunction
CONSULT–II dis-
play item
Diagnosis content
Communication
malfunction
COMM DATA
Communicating with each LCU is judged normal when communication is normally
completed and when both transmitted data and received data are equal. In other
cases, it is judged malfunctioning. If the communication is inactive, no diagnosis
result is displayed.
Inactive communi-
cation
NO RESPONSE
Communicating with each LCU is judged normal when at least 1 communication is
normally completed within 3 trials. In other cases, it is judged malfunctioning.
Sleep malfunction
SLEEP
Check that each LCU switches to sleep mode.
Communication
malfunction*
PAST COMM
DATA
The records when communication signal, malfunctions were continuously detected
while the communication was normal are displayed, or a malfunction was detected
during the sleep control in the past are displayed.
Inactive communi-
cation*
PAST NO
RESPONSE
The records when inactive communications were continuously detected while the
communication was normal are displayed.
AUTOMATIC DRIVE POSITIONER
SE-41
C
D
E
F
G
H
J
K
L
M
A
B
SE
4.
Touch “NEXT” to select the local control unit (LCU) to be diagnosed.
5.
Check that any malfunction is displayed. If necessary, touch “PRINT” to keep the record.
6.
Carry out the inspection of the malfunctioning item.
Trouble Diagnosis Chart
NOTE:
●
For a specific local control unit (LCU), either “PAST COMM DATA” or “PAST NO RESPONSE” may be displayed instead of the
above results.The data record, causes this, so erase the records.
(The display only shows the incident records, they are not malfunctions caused during the diagnosis. One possible cause is that an
intermittent incident occurred.)
●
Follow the steps below to erase the memory.
Carry out either disconnect BCM battery power supply or erase memory with CONSULT-II.
●
With the battery connected, if the local control unit (LCU) connector is disconnected and left for approximately 1 minute, the BCM
stores “NO RESPONSE” record.
COMMUNICATION SYSTEM A
1.
CHECK BCM
Replace the BCM with a known-good one, and carry out the communication diagnosis. Refer to
.
OK or NG
OK
>> The harness and connector is checked, and it is normal, replace BCM
NG
>> GO TO 2.
Malfunctioning
item
Display unit
CONSULT–II IVMS communication diagnosis
content
Self-diagnosis
trouble code
No.
Malfunctioning system
and reference
COMM DATA
One LCU is dis-
played.
POWER WINDOW C/U–DR "COMMDATA"
24
Replace the displayed
LCU.
DOOR MIRROR C/U–RH "COMMDATA"
27
DOOR MIRROR C/U–LH "COMMDATA"
37
POWER SEAT C/U–DR "COMMDATA"
47
Multiple LCUs
are displayed.
BCM
"COMMFAIL1"L1","COMMFAIL2"
Displays in
order of 24
→
27
→
37
→
47
→
and cycles
from 24.
Communication system A:
Refer to
NO
RESPONSE
One LCU is dis-
played.
POWER WINDOW C/U–DR "NORESPONSE"
25
Communication system B:
Refer to
DOOR MIRROR C/U–RH "NORESPONSE"
28
DOOR MIRROR C/U–LH "NORESPONSE"
38
POWER SEAT C/U–DR "NORESPONSE"
48
Multiple LCUs
are displayed.
BCM/HARNESS
Displays in
order of
25
→
28
→
38
→
4
8 and cycles
from 25.
Communication system
C: Refer to
SLEEP malfunc-
tion
One LCU is dis-
played.
POWER WINDOW C/U–DR "SLEEP"
No self-diagno-
sis function
Replace the displayed
LCU.
DOOR MIRROR C/U–RH
"SLEEP"
DOOR MIRROR C/U–LH
"SLEEP"
POWER SEAT C/U–DR
"SLEEP"
Multiple LCUs
are displayed.
All the above control units are displayed.
No self-diagno-
sis function
Communication system A:
Refer to
SE-42
AUTOMATIC DRIVE POSITIONER
2.
CHECK LCU
1.
Replace with the previously installed BCM.
2.
Replace the LCU with a known-good one, and carry out the communication diagnosis. Refer to
"IVMS Communication Diagnosis"
OK or NG
OK
>> The harness and connector is checked, and it is normal, replace LCU
NG
>> Repair or replace harness between the LCU and BCM.
COMMUNICATION SYSTEM B
1.
CHECK HARNESS CONNECTOR
Check terminals (at the control unit and harness) on the malfunctioning LCU for disconnection, bend, loose
connection, and other malfunctions.
OK or NG
OK
>> GO TO 2.
NG
>> Repair the terminals and connectors.
2.
CHECK LCU
Replace the malfunctioning LCU with a known-good one, and carry out the communication diagnosis. Refer to
SE-40, "IVMS Communication Diagnosis"
.
OK or NG
OK
>> The harness and connector is checked, and it is normal, replace LCU
NG
>> Repair the harness between the indicated LCU and BCM.
COMMUNICATION SYSTEM C
1.
CHECK HARNESS CONNECTOR
Check terminals (at the control unit and harness) on BCM and LCU for disconnection, bend, loose connection,
and other malfunctions.
OK or NG
OK
>> GO TO 2.
NG
>> Repair the terminals and connectors.
2.
CHECK BCM
Replace the malfunctioning BCM with a known-good one, and carry out the communication diagnosis. Refer
to
SE-40, "IVMS Communication Diagnosis"
OK or NG
OK
>> The harness and connector is checked, and it is normal, replace BCM
NG
>> Repair the harness between the LCU and BCM control.
WORK SUPPORT
Display Item List
Refer to
SE-36, "SETTING CHANGE FUNCTION"
.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст