Infiniti F50. Manual — part 765
AUTOMATIC DRIVE POSITIONER
SE-51
C
D
E
F
G
H
J
K
L
M
A
B
SE
Cancel Of Switch Monitor
If one of the following conditions is satisfied, the switch monitor is cancelled.
●
When the ignition switch is turned OFF.
●
The vehicle speed becomes 7 km/h (4 MPH) or higher.
ON BOARD DIAGNOSIS FOR AUTOMATIC DRIVE POSITIONER
Check the operations of the auto drive positioner system.
*1: If no malfunction is indicated, On board diagnosis for automatic drive positioner will end after the vehicle
speed sensor diagnosis is performed.
*2: Diagnosis ends after self-diagnostic results have been indicated for 10 minutes if left unattended.
PIIA4472E
SE-52
AUTOMATIC DRIVE POSITIONER
Diagnostic Result Display
●
The malfunctioning items are indicated by how many times LEDs on the seat memory switches 1 and 2
flash simultaneously.
●
If the vehicle speed is less than 7 km/h (4 MPH) for 15 seconds after the diagnosis for the seat and steer-
ing wheel systems were completed, the vehicle speed signal is judged malfunctioning.
●
If LH door mirror is malfunctioning, only indicator lamp on the memory switch 1 flashes, and if RH door
mirror is malfunctioning, only indicator lamp on the memory switch 2 flashes.
●
When all the diagnosis are finished normally, the indicator lamps on the memory switches 1 and 2 go off
after the vehicle speed signal diagnosis.
●
If there are multiple malfunctioning parts, the lamps indicate them in sequence from the smallest diagno-
sis trouble code.
●
The diagnosis results repeat until the diagnosis mode is cancelled.
PIIA0190E
AUTOMATIC DRIVE POSITIONER
SE-53
C
D
E
F
G
H
J
K
L
M
A
B
SE
Symptom Chart
EIS0041M
Symptom
Diagnoses / service procedure
Refer to
page
A part of seat system does not operate (both automati-
cally and manually).
1. Seat sliding motor circuit inspection
2. Seat reclining motor circuit inspection
3. Front lifting motor circuit inspection
4. Rear lifting motor circuit inspection
5. If the above systems are normal, replace the BCM
—
A part of steering wheel system does not operate (both
automatically and manually).
1.Steering wheel telescopic motor circuit inspection
2. Steering wheel tilt motor circuit inspection
3. If the above systems are normal, replace the BCM
—
Door mirrors cannot be actuated in both automatic and
manual modes.
1. Door mirror remote control switch (changeover switch)
circuit inspection
2. Door mirror remote control switch (mirror switch) sys-
tem inspection
3. If the above systems are normal, replace the BCM.
–
A part of seat system does not operate (only automatic
operation).
1. Seat sliding sensor circuit inspection
2. Seat reclining sensor circuit inspection
3. Front lifting sensor circuit inspection
4. Rear lifting sensor circuit inspection
5. If the above systems are normal, replace the driver
seat control unit
–
Door mirrors cannot be actuated in automatic mode.
1. R-position signal circuit inspection
2. Mirror sensor circuit inspection 1
3. If the above systems are normal, replace the door mir-
ror control unit.
–
All the automatic operations do not operate.
1. Detente switch circuit inspection
2. Telescopic sensor circuit inspection
3. Tilt sensor circuit inspection
4. Vehicle speed signal inspection
5. If all the above systems are normal, replace the BCM
–
Seat or steering wheel memory does not work.
1. Seat memory switch circuit inspection
2. If the above systems are normal, replace the BCM.
–
Only manual operation does not operate.
1. Seat sliding switch circuit inspection
2. Seat reclining switch circuit inspection
3. Front end seat lifter switch circuit inspection
4. Rear end seat lifter switch circuit inspection
5. Steering wheel telescoping switch circuit inspection
6. Steering wheel tilt system switch circuit inspection
7. Door mirror remote control switch (mirror switch) cir-
cuit inspection
8. If all the above systems are normal, replace the driver
seat control unit for the seat system, the BCM for the
steering wheel system
–
The entry / exiting does not operated when door is
opened and closed (The entry / exiting operates with key
switch)
1. Seat memory indicator lamp circuit inspection
2. If the above systems are normal, replace the BCM.
–
SE-54
AUTOMATIC DRIVE POSITIONER
Seat memory indicator lamps 1 and 2 do not illuminate.
1. Driver door switch circuit inspection
2. If the above systems are normal, replace the BCM.
–
Auto driving position system self-diagnosis does not
work.(With out CONSULT-II)
1. Detention switch circuit inspection
2. Key switch and key lock solenoid circuit inspection
3. Seat memory switch circuit inspection
4. Seat memory indicator lamp circuit inspection
5. Vehicle speed signal inspection
6. If all the above systems are normal, retry the self-diag-
nosis. If the self-diagnosis are still disable, check the
driver seat control unit connector and terminals for loose-
ness and damage.
–
Lumber support motor does not operated.
1. Lumber support circuit inspection
Turnout operation of rear power seat LH does not oper-
ate, bat rear power seat can be operated by rear power
seat switch.
1. Turnout operation inspection.
Symptom
Diagnoses / service procedure
Refer to
page
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст