Infiniti F50. Manual — part 660
INTERIOR ROOM LAMP
LT-107
C
D
E
F
G
H
I
J
L
M
A
B
LT
Bulb Replacement
EKS000WN
MAP LAMP (FRONT PERSONAL LIGHT) AND CONSOLE LAMP (CONSOLE LIGHT)
Map Lamp
1.
Remove the finisher using a clip driver or a suitable tool.
2.
Insert a thin screwdriver in the notch and remove the lens.
3.
Remove the screw and remove the shade.
4.
Remove the bulb.
Console Lamp
1.
Remove the front interior lamp. Refer to
.
2.
Turn the console lamp bulb socket counterclockwise and unlock it.
PERSONAL LAMP (REAR PERSONAL LIGHT)
1.
Remove the rear interior lamp. Refer to
in “Removal and Installation”.
2.
Unfold the tabs and remove the lens.
3.
Remove the shade mounting screw and remove the shade from
the personal lamp.
4.
Remove the bulb.
Removal and Installation
EKS000U4
FRONT INTERIOR LAMP
1.
Open the front interior lamp box and remove the screw.
2.
Insert a clip driver or a suitable tool and disengage the metal clip
fittings of the front interior lamp.
3.
Disconnect the connector and remove the front interior lamp.
REAR INTERIOR LAMP
1.
Using a clip driver or a suitable tool, press and remove the metal
clip of the rear interior lamp.
2.
Disconnect the rear interior lamp connector.
Map lamp (Front personal light)
: 12V 8W
PKIA0177E
Console lamp (Console light)
: 12V 1.4W
Personal lamp (Rear personal light)
: 12V 8W
PKIA0073E
PKIA0068E
PKIA0074E
LT-108
INTERIOR ROOM LAMP
IGNITION KEY HOLE ILLUMINATION
1.
Remove the lower instrument panel (driver side). Refer to
in “INSTRUMENT PANEL (IP)” sec-
tion.
2.
Turn the bulb socket counterclockwise and unlock it.
Ignition key hole illumination
: 12V 1.4W
PKIA0187E
STEP LAMP
LT-109
C
D
E
F
G
H
I
J
L
M
A
B
LT
STEP LAMP
PFP:26420
Component Parts and Harness Connector Location
EKS000ZR
SKIA3839E
LT-110
STEP LAMP
System Description
EKS0017S
POWER SUPPLY AND GROUND
Power is supplied at all times
●
to BCM terminal 105
●
through 10A fuse [No. 3, located in the fuse block (J/B) No. 1], and
●
to all step lamps terminal 1
●
through 10A fuse [No. 8, located in the fuse block (J/B) No. 1].
Ground is supplied to terminal 15 of driver door control unit through body grounds M24 and M114.
Ground is supplied to terminal 7 of passenger door control unit through body grounds M24 and M114.
Ground is also supplied to terminal 7 of rear LH door control unit and rear RH door control unit through body
grounds B17 and B57 or B217 and B256.
OPERATING PROCEDURE
BCM is connected to driver door control unit as DATA LINE A-3.
Then driver door control unit is connected to each door control unit.
When any door switch is in OPEN position, ground is supplied
●
to BCM terminal 33, 37, 142, or 143
●
through driver side, passenger side, rear LH or RH door switch.
Then BCM sends a signal to the driver door control unit (LCU 01) to turn on step lamp. With ground supplied,
step lamp turns on.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст