Infiniti QX56 (Z62). Manual — part 460
DLN-40
< BASIC INSPECTION >
[TRANSFER: ATX90A]
DIAGNOSIS AND REPAIR WORK FLOW
Other conditions
Memo
Interview sheet
Customer
name
MR/MS
Registration
number
Initial year reg-
istration
Vehicle type
VIN
Storage
date
Engine
Mileage
km (
Mile)
ADDITIONAL SERVICE WHEN REPLACING TRANSFER CONTROL UNIT
DLN-41
< BASIC INSPECTION >
[TRANSFER: ATX90A]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
ADDITIONAL SERVICE WHEN REPLACING TRANSFER CONTROL UNIT
Description
INFOID:0000000006222234
Perform writing unit parameter and initial calibration after replacing transfer control unit. Refer to
.
Work Procedure
INFOID:0000000006222235
NOTE:
In fail-safe mode, can not perform work support. (Except that DTC P181F is detected.)
1.
WRITE UNIT PARAMETER
Perform writing unit parameter to control unit. Refer to
>> GO TO 2.
2.
INITIAL CALIBRATION (1)
With CONSULT-III
1.
Start the engine.
CAUTION:
Never drive the vehicle.
2.
Check “4WD MODE”, “T/M RANGE”, “COMER VHCL SPEED”, “MOTOR POWER SUP” of CONSULT-III
“DATA MONITOR” for “ALL MODE AWD/4WD”.
3.
Continue the following condition more than 10 seconds.
Does the transfer motor operate automatically?
YES
>> After the transfer motor operation stop (After approximately 10 seconds) GO TO 4.
NO
>> GO TO 3.
3.
INITIAL CALIBRATION (2)
With CONSULT-III
1.
Select “START CALIBRATION” of CONSULT-III “WORK SUPPORT” for “ALL MODE AWD/4WD”.
2.
Wait until the motor operation stop. (After approximately 10 seconds)
>> GO TO 4.
4.
PERFORM SELF-DIAGNOSIS
With CONSULT-III
1.
Erase self-diagnosis result for “ALL MODE AWD/4WD”.
2.
Turn the ignition switch ON to OFF.
CAUTION:
Wait for 10 seconds after turning ignition switch OFF.
3.
Start the engine.
CAUTION:
Never drive the vehicle.
4.
Perform self-diagnosis for “ALL MODE AWD/4WD”.
Is “DTC P181F” detected?
YES
>> GO TO 1.
NO
>> WORK END
4WD MODE
: AUTO
T/M RANGE
: N
COMPER VHCL SPEED
: 0 km/h (Never drive the vehicle)
MOTOR POWER SUP
: More than 11 V
DLN-42
< BASIC INSPECTION >
[TRANSFER: ATX90A]
ADDITIONAL SERVICE WHEN REPLACING TRANSFER ASSEMBLY
ADDITIONAL SERVICE WHEN REPLACING TRANSFER ASSEMBLY
Description
INFOID:0000000006222236
Perform writing unit parameter, transfer fluid viscosity learning and initial calibration after replacing transfer
assembly. Refer to
.
Work Procedure
INFOID:0000000006222237
NOTE:
In fail-safe mode, can not perform work support. (Except that DTC P181F is detected.)
1.
WRITE UNIT PARAMETER
Perform writing unit parameter to control unit. Refer to
>> GO TO 2.
2.
PREPARATION BEFORE WORK
With CONSULT-III
1.
Start the engine.
CAUTION:
Never drive the vehicle.
2.
Check “4WD MODE”, “T/M RANGE”, “COMER VHCL SPEED”, “MOTOR POWER SUP” of CONSULT-III
“DATA MONITOR” for “ALL MODE AWD/4WD”.
3.
Continue the following condition more than 10 seconds.
>> GO TO 3.
3.
PERFORM TRANSFER FLUID VISCOSITY LEARNING
With CONSULT-III
1.
Select “OIL DETERIORATION INFO RESET” of CONSULT-III “WORK SUPPORT” for “ALL MODE AWD/
4WD”.
2.
Select “Start”.
>> GO TO 4.
4.
INITIAL CALIBRATION
With CONSULT-III
1.
Select “START CALIBRATION” of CONSULT-III “WORK SUPPORT” for “ALL MODE AWD/4WD”.
2.
Wait until the motor operation stop. (After approximately 10 seconds)
>> GO TO 5.
5.
PERFORM SELF-DIAGNOSIS
With CONSULT-III
1.
Erase self-diagnosis result for “ALL MODE AWD/4WD”.
2.
Turn the ignition switch ON to OFF.
CAUTION:
Wait for 10 seconds after turning ignition switch OFF.
3.
Start the engine.
CAUTION:
Never drive the vehicle.
4.
Perform self-diagnosis for “ALL MODE AWD/4WD”.
4WD MODE
: AUTO
T/M RANGE
: N
COMPER VHCL SPEED
: 0 km/h (Never drive the vehicle)
MOTOR POWER SUP
: More than 11 V
ADDITIONAL SERVICE WHEN REPLACING TRANSFER ASSEMBLY
DLN-43
< BASIC INSPECTION >
[TRANSFER: ATX90A]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
Is “DTC P181F” detected?
YES
>> GO TO 1.
NO
>> WORK END
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст