Infiniti QX56 (Z62). Manual — part 174
BODY CONSTRUCTION
BRM-23
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
BRM
N
O
P
10. Lower dash reinforcement
11.
Lower dash
12. Lower hinge plate (Front)
13. Lower front pillar hinge brace
14. Front floor
15. 2nd body mounting member
16. 2nd body mounting bracket
17. Inner sill
18. Center sill reinforcement
19. Outer sill reinforcement
20. Side member outrigger
21. Inner center pillar
22. Inner center pillar reinforcement
23. Upper outer center pillar reinforce-
ment
24. Center pillar hinge brace
25. Center pillar plate
26. Lower hinge plate (Rear)
27. Lower center pillar bracket
28. 3rd body mounting bracket
29. Rear floor front
30. Outer sill rear reinforcement
31. Anchor plate
32. Outer rear wheelhouse
33. Sill closing plate
34. Inner rear pillar
35. Inner side panel reinforcement
36. Roof rail rear brace
37. Inner back pillar
38. Inner rear roof side rail
39. Back pillar reinforcement
40. Upper back pillar main
41. Back pillar seat belt anchor
BRM-24
< REMOVAL AND INSTALLATION >
REPLACEMENT OPERATIONS
REPLACEMENT OPERATIONS
Description
INFOID:0000000006248496
• This section is prepared for technicians who have attained a high level of skill and experience in repairing
collision-damaged vehicles and also use modern service tools and equipment. Persons unfamiliar with body
repair techniques should not attempt to repair collision-damaged vehicles by using this section.
• Technicians are also encouraged to read the Body Repair Manual (Fundamentals) in order to ensure that the
original functions and quality of the vehicle are maintained. The Body Repair Manual (Fundamentals) con-
tains additional information, including cautions and warnings, that are not including in this manual. Techni-
cians should refer to both manuals to ensure proper repair.
• Please note that this information is prepared for worldwide usage, and as such, certain procedures might not
apply in some regions or countries.
The symbols used in this section for welding operations are shown below.
Symbol marks
Description
2-spot welds
3-spot welds
MIG plug weld
For 3 panels plug weld method
MIG seam weld / Point weld
JSKIA0049ZZ
JSKIA0053ZZ
JSKIA0050ZZ
JSKIA0051ZZ
JSKIA0054ZZ
JSKIA0055ZZ
JSKIA0052ZZ
JSKIA0056ZZ
REPLACEMENT OPERATIONS
BRM-25
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
BRM
N
O
P
• Front pillar butt joint can be determined anywhere within shaded
area as shown in the figure. The best location for the butt joint is at
position A due to the construction of the vehicle.
• Determine cutting position and record distance from the locating
indent. Use this distance when cutting the service part. Cut outer
front pillar over 60 mm (2.36 in) above the inner front pillar cut
position.
• Prepare a cutting jig to make outer pillar easier to cut. Also, this will
permit the service part to be accurately cut at the joint position.
• An example of cutting operation using a cutting jig is as per the fol-
lowing.
1.
Mark cutting lines.
A: Cut position of outer pillar
B: Cut position of inner pillar
2.
Align cutting line with notch on jig. Clamp jig to pillar.
3.
Cut outer pillar along groove of jig (at position A).
4.
Remove jig and cut remaining portions.
5.
Cut inner pillar at position B in same manner.
PIIA0150E
JSKIA0104GB
JSKIA0105GB
PIIA0153E
BRM-26
< REMOVAL AND INSTALLATION >
REPLACEMENT OPERATIONS
Radiator Core Support
INFOID:0000000006248497
Hoodledge
INFOID:0000000006248498
Work after radiator core support is removed.
: Vehicle front
: Weld the parts onto the back of the component part.
Replacement parts
z
Side radiator core support (LH)
JSKIA1914ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст