Infiniti QX56 (Z62). Manual — part 652
EM-48
< REMOVAL AND INSTALLATION >
FUEL INJECTOR AND FUEL TUBE
FUEL INJECTOR AND FUEL TUBE
Exploded View
INFOID:0000000006289556
CAUTION:
• Never remove or disassemble parts unless instructed as shown in the figure.
• Be sure to follow the tightening instruction to avoid fuel leakage.
1.
Fuel tube insulator (bank 2)
2.
Fuel tube insulator (center)
3.
Fuel tube insulator (bank 1)
4.
High pressure fuel pump
5.
Fuel feed tube (pump side)
6.
Fuel feed tube (bank side)
7.
Fuel rail (bank 2)
8.
Injector holder
9.
O-ring (blue)
10. Backup ring
11. Fuel injector
12. Seal ring
13. Insulator
14. Fuel rail (bank 1)
15. Gasket
16. Fuel rail pressure sensor
A.
Comply with the installation proce-
dure when tightening. Refer to
49, "Removal and Installation"
.
Refer to
for symbols in the figure.
JPBIA3506GB
FUEL INJECTOR AND FUEL TUBE
EM-49
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
Removal and Installation
INFOID:0000000006289557
REMOVAL
WARNING:
EM-4, "Precaution for Handling High Pressure Fuel System"
when working on the
high pressure fuel system.
• Put a “CAUTION: FLAMMABLE” sign in the workshop.
• Be sure to work in a well ventilated area and furnish workshop with a CO
2
fire extinguisher.
• Never smoke while servicing fuel system. Keep open flames and sparks away from the work area.
• To avoid the danger of being scalded, never drain engine coolant when engine is hot.
1.
Release fuel pressure. Refer to
2.
Remove intake manifold. Refer to
EM-30, "Removal and Installation"
3.
Remove fuel feed tube (pump side) and fuel feed tube (bank side).
CAUTION:
Never reuse fuel feed tube.
4.
Remove fuel rail (bank 1) and fuel rail (bank 2).
5.
Disconnect harness connector from fuel injectors.
6.
Remove fuel injector from cylinder head as per the following:
CAUTION:
• Be careful with remaining fuel that may go out from fuel tube.
• Be careful not to damage injector nozzles during removal.
• Never bump or drop fuel injector.
• Never disassemble fuel injector.
a.
Remove injector holder.
b.
Install an injector remover [SST: KV10119600 (—)] (A) to the
injector connector side so that cutout (B) of injector remover
faces the injector connector side.
• Hook pawl portion (B) of injector remover [SST: KV10119600
(—)] (A) to groove portion (C) of injector.
JSBIA0342ZZ
JSBIA0343ZZ
EM-50
< REMOVAL AND INSTALLATION >
FUEL INJECTOR AND FUEL TUBE
c.
Press down body portion (A) of injector remover [SST:
KV10119600 (—)] until it contacts cylinder head.
d.
Tighten injector remover [SST: KV10119600 (—)] clockwise and
remove injector from cylinder head.
e.
Cut Teflon seal (1) while pinching it. Be careful not to damage
injector.
f.
Remove insulator from mounting hole of fuel injector of cylinder
head.
INSTALLATION
1.
Install seal ring to fuel injector as per the following:
CAUTION:
• Handle seal ring with bare hands. Never wear gloves.
• Never apply engine oil to seal ring.
• Never clean seal ring with solvent.
JPBIA3747ZZ
JPBIA3748ZZ
JSBIA0346ZZ
FUEL INJECTOR AND FUEL TUBE
EM-51
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
a.
Install an injector seal drift set [SST: KV101197S0 (—)] (A) to
fuel injector (1).
b.
Set seal ring (1) to injector seal drift set [SST: KV101197S0 (—)]
(A).
c.
Straightly insert seal ring (1), which is set in step 2, to fuel injec-
tor as shown in the figure and install.
CAUTION:
Be careful that seal ring does not exceed the groove portion
of fuel injector.
d.
Insert injector seal drift set [SST: KV101197S0 (—)] (A) to injec-
tor and rotate clockwise and counterclockwise by 90
°
while
pressing seal ring to fit it.
NOTE:
Compress seal ring, because this operation is for rectifying
stretch of seal ring caused by installation and for preventing
sticking when inserting injector into cylinder head.
2.
Install O-ring and backup ring to fuel injector. When handing new O-ring and backup ring, paying attention
to the following caution items:
CAUTION:
• Handle O-ring with bare hands. Never wear gloves.
• Lubricate O-ring with new engine oil.
• Never clean O-ring with solvent.
• Check that O-ring and its mating part are free of foreign material.
• When installing O-ring, be careful not to scratch it with tool or fingernails. Also be careful not to
twist or stretch O-ring. If O-ring was stretched while it was being attached, never insert it quickly
into fuel tube.
• Insert new O-ring straight into fuel rail. Never decenter or twist it.
JSBIA0347ZZ
JSBIA0348ZZ
JSBIA0350ZZ
JSBIA0351ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст