Infiniti QX56 (Z62). Manual — part 683
EXL-24
< SYSTEM DESCRIPTION >
[XENON TYPE]
DIAGNOSIS SYSTEM (BCM)
*
1
: Factory setting
*
2
: For models for Canada, this item is displayed but is not operated.
DATA MONITOR
BATTERY SAVER SET
On*
1
With the exterior lamp battery saver function
Off
Without the exterior lamp battery saver function
ILL DELAY SET
MODE 1*
1
45 sec.
Sets delay timer function timer operation time
(All doors closed)
MODE 2
Without the
function
MODE 3
30 sec.
MODE 4
60 sec.
MODE 5
90 sec.
MODE 6
120 sec.
MODE 7
150 sec.
MODE 8
180 sec.
AUTO LIGHT LOGIC SET*
2
MODE 1*
1
With twilight ON custom & with wiper INT, LO and HI
MODE 2
With twilight ON custom & with wiper LO and HI
MODE 3
With twilight ON custom & without
MODE 4
Without twilight ON custom & with wiper INT, LO and HI
MODE 5
Without twilight ON custom & with wiper LO and HI
MODE 6
Without twilight ON custom & without
Service item
Setting item
Setting
Monitor item
[Unit]
Description
PUSH SW
[On/Off]
The switch status input from push-button ignition switch
ENGINE STATE
[Stop/Stall/Crank/Run]
The engine status received from ECM via CAN communication
VEH SPEED 1
[km/h]
The value of the vehicle speed received from combination meter via CAN communi-
cation
TURN SIGNAL R
[On/Off]
Each switch status that BCM judges from the combination switch reading function
TURN SIGNAL L
[On/Off]
TAIL LAMP SW
[On/Off]
HI BEAM SW
[On/Off]
HEAD LAMP SW1
[On/Off]
HEAD LAMP SW2
[On/Off]
PASSING SW
[On/Off]
AUTO LIGHT SW
[On/Off]
FR FOG SW
[On/Off]
RR FOG SW
[On/Off]
NOTE:
This item is indicated, but can not monitored
DIAGNOSIS SYSTEM (BCM)
EXL-25
< SYSTEM DESCRIPTION >
[XENON TYPE]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
ACTIVE TEST
*: Only models for Canada display this item.
FLASHER
FLASHER : CONSULT-III Function (BCM - FLASHER)
INFOID:0000000006213912
WORK SUPPORT
DOOR SW-DR
[On/Off]
The switch status input from front door switch (driver side)
DOOR SW-AS
[On/Off]
The switch status input from front door switch (passenger side)
DOOR SW-RR
[On/Off]
The switch status input from rear door switch RH
DOOR SW- RL
[On/Off]
The switch status input from rear door switch LH
DOOR SW-BK
[On/Off]
The switch status input from back door switch
OPTICAL SENSOR
[On/Off]
The sensor status input from optical sensor
OPTI SEN (DTCT)
[V]
The value of outside brightness voltage input from the optical sensor
OPTI SEN (FILT)
[V]
The value of outside brightness voltage filtered by BCM
Monitor item
[Unit]
Description
Test item
Operation
Description
TAIL LAMP
On
Transmits the position light request signal to IPDM E/R via CAN commu-
nication to turn the tail lamp ON
Off
Stops the tail lamp request signal transmission
HEAD LAMP
Hi
Transmits the high beam request signal via CAN communication to turn
the headlamp (HI)
Lo
Transmits the low beam request signal via CAN communication to turn
the headlamp (LO)
Off
Stops the high & low beam request signal transmission
FR FOG LAMP
On
Transmits the front fog lights request signal to IPDM E/R via CAN com-
munication to turn the front fog lamp ON
Off
Stops the front light request signal transmission
RR FOG LAMP
On
NOTE:
This item is indicated, but can not tested
Off
DAYTIME RUNNING LIGHT*
On
Transmits the front fog lights request signal to IPDM E/R via CAN com-
munication to turn the front fog lamp ON (daytime running light system)
Off
Stops the front light request signal transmission (daytime running light
system)
ILL DIM SIGNAL
On
• Transmits the dimmer signal to combination meter via CAN communi-
cation and dims combination meter
• Transmits the dimmer signal to AV control unit and dims display
Off
Stops the dimmer signal transmission
EXL-26
< SYSTEM DESCRIPTION >
[XENON TYPE]
DIAGNOSIS SYSTEM (BCM)
*: Factory setting
DATA MONITOR
ACTIVE TEST
Service item
Setting item
Setting
HAZARD ANSWER
BACK
Lock Only
With locking only
Sets the hazard warning lamp answer back function
when the door is lock/unlock with the request switch or
the key fob.
Unlk Only
With unlocking only
Lock&Unlk
*
With locking/unlocking
Off
Without the function
Monitor item
[Unit]
Description
REQ SW-DR
[On/Off]
The switch status input from the request switch (driver side)
REQ SW-AS
[On/Off]
The switch status input from the request switch (passenger side)
PUSH SW
[On/Off]
The switch status input from the push-button ignition switch
TURN SIGNAL R
[On/Off]
Each switch status that BCM detects from the combination switch reading function
TURN SIGNAL L
[On/Off]
HAZARD SW
[On/Off]
The switch status input from the hazard switch
RKE-LOCK
[On/Off]
Lock signal status received from the remote keyless entry receiver
RKE-UNLOCK
[On/Off]
Unlock signal status received from the remote keyless entry receiver
RKE-PANIC
[On/Off]
Panic alarm signal status received from the remote keyless entry receiver
Test item
Operation
Description
FLASHER
RH
Outputs the voltage to blink the right side turn signal lamps.
LH
Outputs the voltage to blink the left side turn signal lamps.
Off
Stops the voltage to turn the turn signal lamps OFF.
DIAGNOSIS SYSTEM (IPDM E/R)
EXL-27
< SYSTEM DESCRIPTION >
[XENON TYPE]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
DIAGNOSIS SYSTEM (IPDM E/R)
Diagnosis Description
INFOID:0000000006368066
AUTO ACTIVE TEST
Description
In auto active test, the IPDM E/R sends a drive signal to the following systems to check their operation.
• Oil pressure warning lamp
• Rear window defogger
• Front wiper (LO, HI)
• Parking lamp
• License plate lamp
• Tail lamp
• Side marker lamp
• Front fog lamp
• Headlamp (LO, HI)
• A/C compressor (magnet clutch)
Operation Procedure
CAUTION:
Never perform auto active test in the following conditions.
• Engine is running.
• CONSULT-III is connected.
1.
Close the hood and lift the wiper arms from the windshield. (Prevent windshield damage due to wiper
operation)
NOTE:
When auto active test is performed with hood opened, sprinkle water on windshield beforehand.
2.
Turn the ignition switch OFF.
3.
Turn the ignition switch ON, and within 20 seconds, press the driver door switch 10 times. Then turn the
ignition switch OFF.
CAUTION:
Close passenger door.
4.
Turn the ignition switch ON within 10 seconds. After that the horn sounds once and the auto active test
starts.
CAUTION:
Engine starts when ignition switch is turned ON while brake pedal is depressed.
5.
The oil pressure warning lamp starts blinking when the auto active test starts.
6.
After a series of the following operations is repeated 3 times, auto active test is completed.
NOTE:
• When auto active test has to be cancelled halfway through test, turn the ignition switch OFF.
• When auto active test is not activated, door switch may be the cause. Check door switch. Refer to
Inspection in Auto Active Test
When auto active test is actuated, the following operation sequence is repeated 3 times.
Operation
sequence
Inspection location
Operation
1
Oil pressure warning lamp
Blinks continuously during operation of auto active test
2
Rear window defogger
10 seconds
3
Front wiper
LO for 5 seconds
→
HI for 5 seconds
4
• Parking lamp
• License plate lamp
• Tail lamp
• Side marker lamp
• Front fog lamp
10 seconds
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст