Infiniti QX56 (Z62). Manual — part 801
B263D, B263E, B263F INTAKE DOOR MOTOR
HAC-95
< DTC/CIRCUIT DIAGNOSIS >
[AUTOMATIC AIR CONDITIONING]
C
D
E
F
G
H
J
K
L
M
A
B
HAC
N
O
P
B263D, B263E, B263F INTAKE DOOR MOTOR
DTC Logic
INFOID:0000000006275929
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
PERFORM DTC CONFIRMATION PROCEDURE
With CONSULT-III
1.
Turn ignition switch ON.
2.
Select “Self Diagnostic Result” mode of “HVAC” using CONSULT-III.
3.
Check DTC.
Is DTC detected?
YES
>> Refer to
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000006275930
1.
CHECK INTAKE DOOR MOTOR COMMUNICATION SIGNAL
1.
Turn ignition switch ON.
2.
Check output waveform between intake door motor harness connector and ground with the oscilloscope.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> GO TO 3.
2.
CHECK INSTALLATION OF INTAKE DOOR MOTOR CONTROL LINKAGE
Check intake door motor control linkage is properly installed. Refer to
.
Is the inspection result normal?
YES
>> Replace intake door motor. Refer to
HAC-153, "INTAKE DOOR MOTOR : Removal and Installa-
.
NO
>> Repair or replace malfunctioning part.
DTC
Items
(CONSULT-III screen terms)
DTC detection condition
Possible cause
B263D
FRE DOOR FAIL
When the malfunctioning intake door
position is detected at FRE position
• Intake door motor
(PBR internal circuit is open or short-
ed)
• Intake door motor control linkage in-
stallation condition
• A/C auto amp.
• Harness and connector
(LIN communication line is open or
shorted)
B263E
20P FRE DOOR FAIL
When the malfunctioning intake door
position is detected at 20% FRE posi-
tion
B263F
REC DOOR FAIL
When the malfunctioning intake door
position is detected at REC position
+
−
Output waveform
Intake door motor
Connector
Terminal
M254
3
Ground
SJIA1453J
HAC-96
< DTC/CIRCUIT DIAGNOSIS >
[AUTOMATIC AIR CONDITIONING]
B263D, B263E, B263F INTAKE DOOR MOTOR
3.
CHECK INTAKE DOOR MOTOR COMMUNICATION SIGNAL CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect intake door motor and A/C auto amp. connector.
3.
Check continuity between intake door motor harness connector and A/C auto amp. harness connector.
Is the inspection result normal?
YES
>> Replace A/C auto amp.. Refer to
HAC-146, "Removal and Installation"
NO
>> Repair harness or connector.
Intake door motor
A/C auto amp.
Continuity
Connector
Terminal
Connector
Terminal
M254
3
M50
16
Existed
B2661, B2662, B2663 UPPER VENTILATOR DOOR MOTOR
HAC-97
< DTC/CIRCUIT DIAGNOSIS >
[AUTOMATIC AIR CONDITIONING]
C
D
E
F
G
H
J
K
L
M
A
B
HAC
N
O
P
B2661, B2662, B2663 UPPER VENTILATOR DOOR MOTOR
DTC Logic
INFOID:0000000006275931
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
PERFORM DTC CONFIRMATION PROCEDURE
With CONSULT-III
1.
Turn ignition switch ON.
2.
Select “Self Diagnostic Result” mode of “HVAC” using CONSULT-III.
3.
Check DTC.
Is DTC detected?
YES
>> Refer to
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000006275932
1.
CHECK UPPER VENTILATOR DOOR MOTOR COMMUNICATION SIGNAL
1.
Turn ignition switch ON.
2.
Check output waveform between upper vent door motor harness connector and ground with the oscillo-
scope.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> GO TO 3.
2.
CHECK INSTALLATION OF UPPER VENTILATOR DOOR MOTOR
Check upper ventilator door motor is properly installed. Refer to
Is the inspection result normal?
YES
>> Replace upper ventilator door motor. Refer to
HAC-154, "UPPER VENTILATOR DOOR MOTOR :
.
DTC
Items
(CONSULT-III screen terms)
DTC detection condition
Possible cause
B2661
UPPER VENT DOOR MOT
When the malfunctioning upper ventila-
tor door position is detected at OPEN
position
• Upper ventilator door motor
(PBR internal circuit is open or short-
ed)
• Upper ventilator door motor installation
condition
• A/C auto amp.
• Harness and connector
(LIN communication line is open or
shorted)
B2662
When the malfunctioning upper ventila-
tor door position is detected at middle
position
B2663
When the malfunctioning upper ventila-
tor door position is detected at shut po-
sition
+
−
Output waveform
Upper vent door motor
Connector
Terminal
M256
3
Ground
SJIA1453J
HAC-98
< DTC/CIRCUIT DIAGNOSIS >
[AUTOMATIC AIR CONDITIONING]
B2661, B2662, B2663 UPPER VENTILATOR DOOR MOTOR
NO
>> Repair or replace malfunctioning part.
3.
CHECK UPPER VENTILATOR DOOR MOTOR COMMUNICATION SIGNAL CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect upper vent door motor and A/C auto amp. connector.
3.
Check continuity between upper vent door motor harness connector and A/C auto amp. harness connec-
tor.
Is the inspection result normal?
YES
>> Replace A/C auto amp.. Refer to
HAC-146, "Removal and Installation"
NO
>> Repair harness or connector.
Upper vent door motor
A/C auto amp.
Continuity
Connector
Terminal
Connector
Terminal
M256
3
M50
16
Existed
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст