Infiniti QX56 (Z62). Manual — part 1195
SR-14
< REMOVAL AND INSTALLATION >
SPIRAL CABLE
SPIRAL CABLE
Exploded View
INFOID:0000000006113053
Removal and Installation
INFOID:0000000006113054
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal and wait 3 minutes
or more.
• Never use the air tools or electric tools for servicing.
REMOVAL
1.
Remove the driver air bag module. Refer to
SR-11, "Removal and Installation"
.
2.
Remove the steering wheel. Refer to
ST-33, "Removal and Installation"
3.
Remove the steering column upper cover and steering column lower cover. Refer to
.
1.
Steering column upper cover
2.
Steering column lower cover
3.
Side lid LH
4.
TORX bolt LH
5.
Driver air bag module
6.
Side lid RH
7.
TORX bolt RH
8.
Steering wheel
9.
Spiral cable
10. Steering angle sensor
11.
Steering column assembly
12. Combination switch
: Pawl
Refer to
for symbols in the figure.
JMHIA1472GB
SPIRAL CABLE
SR-15
< REMOVAL AND INSTALLATION >
C
D
E
F
G
I
J
K
L
M
A
B
SR
N
O
P
4.
Disconnect the spiral cable body side harness connectors (A)
and steering angle sensor harness connector (B).
5.
Remove the spiral cable fixing screws.
6.
Pull out forward the spiral cable and steering sensor.
7.
Remove steering angle sensor. Refer to
BRC-139, "Removal and Installation"
.
CAUTION:
• Never impact the spiral cable.
• Replace the spiral cable if it has been dropped or sustained
an impact.
• Never disassemble the spiral cable.
• Never apply lubricant to the spiral cable.
• Never allow oil, grease, detergent, or water to come in contact with the spiral cable.
INSTALLATION
Note the following item, and install in the reverse order of removal.
CAUTION:
• The spiral cable may snap during steering operation if the
cable is installed in an improper position.
The neutral position is set as follows.
• Carefully turn the spiral cable clockwise to the end position.
Then turn it counterclockwise (about 2 and a half turns) and
stop turning at the mark (B) on which the stopper insertion
holes are in the same position.
• The service part is installed in the neutral position by the
stopper and can be set without adjusting after the stopper is
removed.
• Never over turn the spiral cable or go beyond the number of
turns required. (These will cause the cable to snap.)
• Adjust the spiral cable locating pin (A) to the steering wheel
locating pin hole (C).
JMHIA1486ZZ
JMHIA0009ZZ
JMHIA0879ZZ
SR-16
< REMOVAL AND INSTALLATION >
SPIRAL CABLE
• Fix the driver air bag module harnesses to the harness fixing
hook (A).
• If malfunction is detected by the air bag warning lamp, after repair or replacement of the malfunc-
tioning parts, reset the memory using self-diagnosis or CONSULT-III. Refer to
or
SRC-19, "CONSULT-III Function"
• After the work is completed, check that no system malfunction is detected by air bag warning lamp.
JMHIA1485ZZ
FRONT PASSENGER AIR BAG MODULE
SR-17
< REMOVAL AND INSTALLATION >
C
D
E
F
G
I
J
K
L
M
A
B
SR
N
O
P
FRONT PASSENGER AIR BAG MODULE
Exploded View
INFOID:0000000006113055
Removal and Installation
INFOID:0000000006113056
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal and wait 3 minutes
or more.
• Always work from the side of air bag module. Never work in front of it.
• Never use the air tools or electric tools for servicing.
REMOVAL
1.
Remove the instrument panel assembly. Refer to
IP-14, "Removal and Installation"
.
2.
Remove the front passenger air bag module fixing screws (A).
1.
Instrument panel assembly
2.
Steering member assembly
3.
Front passenger air bag module
Refer to
JMHIA1473GB
JMHIA1487ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст