Infiniti QX56 (Z62). Manual — part 477
DLN-108
< REMOVAL AND INSTALLATION >
[TRANSFER: ATX90A]
4WD MODE SWITCH
4WD MODE SWITCH
Removal and Installation
INFOID:0000000006222328
REMOVAL
NOTE:
4WD shift switch is integrated in 4WD switch assembly.
1.
Remove console finisher assembly from center console assembly. Refer to
2.
Disconnect 4WD switch assembly harness connector.
3.
Press 4WD switch assembly fixing pawls, and remove 4WD switch assembly from console finisher
assembly.
INSTALLATION
Install in the reverse order of removal.
FRONT OIL SEAL
DLN-109
< REMOVAL AND INSTALLATION >
[TRANSFER: ATX90A]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
FRONT OIL SEAL
Exploded View
INFOID:0000000006222329
Removal and Installation
INFOID:0000000006222330
REMOVAL
1.
Remove the drain plug to drain the transfer fluid. Refer to
2.
Remove the front propeller shaft. Refer to
DLN-129, "Removal and Installation"
.
3.
Remove the plug.
4.
Remove the O-ring from the plug.
5.
Remove the snap ring.
6.
Remove the front shaft flange, using a plastic hammer.
7.
Remove the dust shield from the front shaft flange, using puller
and replacer.
8.
Remove front oil seal from front case.
CAUTION:
Never damage the front case.
INSTALLATION
1.
Plug
2.
O-ring
3.
Snap ring
4.
Transfer assembly
5.
Front oil seal
6.
Dust shield
7.
Front shaft flange
: Vehicle front
: Apply transfer fluid. Refer to
MA-10, "Fluids and Lubricants"
Refer to
for symbols not described above.
JPDIE0280GB
A
: Puller (commercial service tool)
B
: Replacer (commercial service tool)
JPDIE0163ZZ
DLN-110
< REMOVAL AND INSTALLATION >
[TRANSFER: ATX90A]
FRONT OIL SEAL
1.
Install front oil seal with a drift (A) (commercial service tool)
within the dimension (L) shown as follows.
CAUTION:
• Never reuse front oil seal.
• Apply transfer fluid onto circumference of oil seal.
2.
Install the dust shield to the front shaft flange.
3.
Install the front shaft flange.
4.
Install the snap ring.
CAUTION:
Never reuse the snap ring.
5.
Install the O-ring to plug.
CAUTION:
• Never reuse the O-ring.
• Never damage the O-ring.
6.
Tighten the plug to specified torque.
7.
Install front propeller shaft. Refer to
DLN-129, "Removal and Installation"
8.
Fill with new transfer fluid, check fluid level and for fluid leakage. Refer to
L
: 5.3 – 5.7 mm
JPDIE0160ZZ
REAR OIL SEAL
DLN-111
< REMOVAL AND INSTALLATION >
[TRANSFER: ATX90A]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
REAR OIL SEAL
Exploded View
INFOID:0000000006222331
Removal and Installation
INFOID:0000000006222332
REMOVAL
1.
Remove the rear propeller shaft. Refer to
DLN-144, "Removal and Installation"
2.
Put matching marks (A) on the end of the main shaft and the
rear companion flange.
CAUTION:
For matching mark, using paint. Never damage main shaft.
3.
Remove the snap ring.
4.
Remove the adjusting shim.
5.
Remove the rear companion flange, using a plastic hammer.
6.
Remove the dust shield from rear companion flange, using the
drift, puller and replacer.
7.
Remove the o-ring from rear companion flange.
8.
Remove the rear oil seal from rear case.
CAUTION:
Never damage rear case and main shaft.
INSTALLATION
1.
Snap ring
2.
Adjusting shim
3.
O-ring
4.
Rear companion flange
5.
Dust shield
6.
Rear oil seal
7.
Transfer assembly
: Vehicle front
: Apply transfer fluid. Refer to
MA-10, "Fluids and Lubricants"
Refer to
for symbols not described above.
JPDIE0281ZZ
JPDIE0162ZZ
A
: Drift [SST: ST30701000 (J-25742-2)]
B
: Puller (commercial service tool)
C
: Replacer (commercial service tool)
JPDIE0159ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст