Infiniti QX56 (Z62). Manual — part 895
LAN
TPMS BRANCH LINE CIRCUIT
LAN-157
< DTC/CIRCUIT DIAGNOSIS >
[CAN SYSTEM (TYPE 2)]
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
TPMS BRANCH LINE CIRCUIT
Diagnosis Procedure
INFOID:0000000006256300
1.
CHECK CONNECTOR
1.
Turn the ignition switch OFF.
2.
Disconnect the battery cable from the negative terminal.
3.
Check the terminals and connectors of the low tire pressure warning control unit for damage, bend and
loose connection (unit side and connector side).
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair the terminal and connector.
2.
CHECK HARNESS FOR OPEN CIRCUIT
1.
Disconnect the connector of low tire pressure warning control unit.
2.
Check the resistance between the low tire pressure warning control unit harness connector terminals.
Is the measurement value within the specification?
YES
>> GO TO 3.
NO
>> Repair the low tire pressure warning control unit branch line.
3.
CHECK POWER SUPPLY AND GROUND CIRCUIT
Check the power supply and the ground circuit of the low tire pressure warning control unit. Refer to
.
Is the inspection result normal?
YES (Present error)>>Replace the low tire pressure warning control unit. Refer to
YES (Past error)>>Error was detected in the low tire pressure warning control unit branch line.
NO
>> Repair the power supply and the ground circuit.
Low tire pressure warning control unit harness connector
Resistance (
Ω
)
Connector No.
Terminal No.
M96
2
1
Approx. 54 – 66
LAN-158
< DTC/CIRCUIT DIAGNOSIS >
[CAN SYSTEM (TYPE 2)]
IPDM-E BRANCH LINE CIRCUIT
IPDM-E BRANCH LINE CIRCUIT
Diagnosis Procedure
INFOID:0000000006256301
1.
CHECK CONNECTOR
1.
Turn the ignition switch OFF.
2.
Disconnect the battery cable from the negative terminal.
3.
Check the following terminals and connectors for damage, bend and loose connection (unit side and con-
nector side).
-
IPDM E/R
-
Harness connector E105
-
Harness connector M77
-
Harness connector M19 (Without ICC system)
-
Harness connector B2 (Without ICC system)
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair the terminal and connector.
2.
CHECK HARNESS FOR OPEN CIRCUIT
1.
Disconnect the connector of IPDM E/R.
2.
Check the resistance between the IPDM E/R harness connector terminals.
Is the measurement value within the specification?
YES
>> GO TO 3.
NO
>> Repair the IPDM E/R branch line.
3.
CHECK POWER SUPPLY AND GROUND CIRCUIT
Check the power supply and the ground circuit of the IPDM E/R. Refer to
Is the inspection result normal?
YES (Present error)>>Replace the IPDM E/R. Refer to
PCS-32, "Removal and Installation"
YES (Past error)>>Error was detected in the IPDM E/R branch line.
NO
>> Repair the power supply and the ground circuit.
IPDM E/R harness connector
Resistance (
Ω
)
Connector No.
Terminal No.
E13
27
26
Approx. 108 – 132
LAN
ADP BRANCH LINE CIRCUIT
LAN-159
< DTC/CIRCUIT DIAGNOSIS >
[CAN SYSTEM (TYPE 2)]
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
ADP BRANCH LINE CIRCUIT
Diagnosis Procedure
INFOID:0000000006256302
1.
CHECK CONNECTOR
1.
Turn the ignition switch OFF.
2.
Disconnect the battery cable from the negative terminal.
3.
Check the following terminals and connectors for damage, bend and loose connection (unit side and con-
nector side).
-
Driver seat control unit
-
Harness connector B460
-
Harness connector B24
-
CAN gateway (With ICC system)
Is the inspection result normal?
YES (With ICC system)>>GO TO 2.
YES (Without ICC system)>>GO TO 3.
NO
>> Repair the terminal and connector.
2.
CHECK HARNESS CONTINUITY (OPEN CIRCUIT)
1.
Disconnect the connector of CAN gateway.
2.
Check the continuity between the CAN gateway harness connector terminals.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Check the harness and repair the root cause (CAN communication circuit 2). Refer to
.
3.
CHECK HARNESS FOR OPEN CIRCUIT
1.
Connect the connector of CAN gateway. (With ICC system)
2.
Disconnect the connector of driver seat control unit.
3.
Check the resistance between the driver seat control unit harness connector terminals.
Is the measurement value within the specification?
YES
>> GO TO 4.
NO
>> Repair the driver seat control unit branch line.
4.
CHECK POWER SUPPLY AND GROUND CIRCUIT
Check the power supply and the ground circuit of the driver seat control unit. Refer to
CONTROL UNIT : Diagnosis Procedure"
Is the inspection result normal?
YES (Present error)>>Replace the driver seat control unit. Refer to
ADP-135, "Removal and Installation"
YES (Past error)>>Error was detected in the driver seat control unit branch line.
NO
>> Repair the power supply and the ground circuit.
CAN gateway harness connector
Continuity
Connector No.
Terminal No.
M125
4
6
Existed
10
12
Existed
Driver seat control unit harness connector
Resistance (
Ω
)
Connector No.
Terminal No.
B451
1
17
Approx. 54 – 66
LAN-160
< DTC/CIRCUIT DIAGNOSIS >
[CAN SYSTEM (TYPE 2)]
PSB BRANCH LINE CIRCUIT
PSB BRANCH LINE CIRCUIT
Diagnosis Procedure
INFOID:0000000006256303
1.
CHECK CONNECTOR
1.
Turn the ignition switch OFF.
2.
Disconnect the battery cable from the negative terminal.
3.
Check the following terminals and connectors for damage, bend and loose connection (unit side and con-
nector side).
-
Pre-crash seat belt control unit (driver side)
-
CAN gateway
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair the terminal and connector.
2.
CHECK HARNESS CONTINUITY (OPEN CIRCUIT)
1.
Disconnect the connector of CAN gateway.
2.
Check the continuity between the CAN gateway harness connector terminals.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Check the harness and repair the root cause (CAN communication circuit 2). Refer to
.
3.
CHECK HARNESS FOR OPEN CIRCUIT
1.
Connect the connector of CAN gateway.
2.
Disconnect the connector of pre-crash seat belt control unit (driver side).
3.
Check the resistance between the pre-crash seat belt control unit (driver side) harness connector termi-
nals.
Is the measurement value within the specification?
YES
>> GO TO 4.
NO
>> Repair the pre-crash seat belt control unit (driver side) branch line.
4.
CHECK POWER SUPPLY AND GROUND CIRCUIT
Check the power supply and the ground circuit of the pre-crash seat belt control unit (driver side). Refer to
Is the inspection result normal?
YES (Present error)>>Replace the seat belt pre-tensioner retractor (LH side). Refer to
RETRACTOR : Removal and Installation"
.
YES (Past error)>>Error was detected in the pre-crash seat belt control unit (driver side) branch line.
NO
>> Repair the power supply and the ground circuit.
CAN gateway harness connector
Continuity
Connector No.
Terminal No.
M125
4
6
Existed
10
12
Existed
Pre-crash seat belt control unit (driver side) harness connector
Resistance (
Ω
)
Connector No.
Terminal No.
B9
14
4
Approx. 54 – 66
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст