Infiniti QX56 (Z62). Manual — part 669
EM-116
< UNIT DISASSEMBLY AND ASSEMBLY >
CYLINDER BLOCK
CONNECTING ROD SIDE CLEARANCE
• Measure the side clearance between connecting rod and crank-
shaft arm with a feeler gauge (A).
• If the measured value exceeds the limit, replace connecting rod,
and measure again. If it still exceeds the limit, replace crankshaft
also.
PISTON TO PISTON PIN OIL CLEARANCE
Piston Pin Hole Diameter
Measure the inner diameter of piston pin hole with an inside
micrometer (A).
Piston Pin Outer Diameter
Measure the outer diameter of piston pin with a micrometer (A).
Piston to Piston Pin Oil Clearance
(Piston to piston pin oil clearance) = (Piston pin hole diameter) – (Piston pin outer diameter)
• If the calculated value is out of the standard, replace piston and piston pin assembly.
• When replacing piston and piston pin assembly, refer to
.
NOTE:
Piston is available together with piston pin as assembly.
PISTON RING SIDE CLEARANCE
Standard and limit
: Refer to
JPBIA2476ZZ
Standard
: Refer to
JPBIA0217ZZ
Standard
: Refer to
JPBIA0218ZZ
Standard
: Refer to
CYLINDER BLOCK
EM-117
< UNIT DISASSEMBLY AND ASSEMBLY >
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
• Measure the side clearance of piston ring (1) and piston ring
groove with a feeler gauge (C).
• If the measured value exceeds the limit, replace piston ring, and
measure again. If it still exceeds the limit, replace piston also.
PISTON RING END GAP
• Check that the cylinder bore inner diameter is within the specifica-
tion.
• Lubricate with new engine oil to piston (1) and piston ring (2), and
then insert piston ring until middle of cylinder with piston, and mea-
sure the piston ring end gap with a feeler gauge (B).
• If the measured value exceeds the limit, replace piston ring, and
measure again. If it still exceeds the limit, re-bore cylinder and use
oversize piston and piston rings.
CONNECTING ROD BEND AND TORSION
• Check with a connecting rod aligner.
• If it exceeds the limit, replace connecting rod assembly.
CONNECTING ROD BIG END DIAMETER
A
: OK
B
: NG
Standard and limit
: Refer to
.
JPBIA2276ZZ
A
: Press-fit
Standard and limit
: Refer to
JPBIA2277ZZ
A
: Bend
B
: Torsion
C
: Feeler gauge
Bend limit
: Refer to
.
Torsion limit
JPBIA0221ZZ
EM-118
< UNIT DISASSEMBLY AND ASSEMBLY >
CYLINDER BLOCK
• Install connecting rod bearing cap without installing connecting rod
bearing, and tighten connecting rod bolts to the specified torque.
Refer to
EM-107, "Disassembly and Assembly"
for the tightening
procedure.
• Measure the inner diameter of connecting rod big end with an
inside micrometer.
• If out of the standard, replace connecting rod assembly.
CONNECTING ROD BUSHING OIL CLEARANCE
Connecting Rod Bushing Inner Diameter
Measure the inner diameter of connecting rod bushing with an inside
micrometer (A).
Piston Pin Outer Diameter
Measure the outer diameter of piston pin with a micrometer (A).
Connecting Rod Bushing Oil Clearance
(Connecting rod bushing oil clearance) = (Connecting rod bushing inner diameter) – (Piston pin outer diame-
ter)
• If the calculated value exceeds the limit, replace connecting rod assembly and/or piston and piston pin
assembly.
• If replacing piston and piston pin assembly, refer to
• If replacing connecting rod assembly, refer to
EM-126, "Connecting Rod Bearing"
to select the connecting
rod bearing.
CYLINDER BLOCK DISTORTION
• Using a scraper, remove gasket on the cylinder block surface, and also remove engine oil, scale, carbon, or
other contamination.
CAUTION:
Be careful not to allow gasket flakes to enter engine oil or engine coolant passages.
1
: Connecting rod
Standard
: Refer to
JPBIA0222ZZ
Standard
: Refer to
JPBIA0223ZZ
Standard
: Refer to
JPBIA0218ZZ
Standard and limit
: Refer to
CYLINDER BLOCK
EM-119
< UNIT DISASSEMBLY AND ASSEMBLY >
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
• Measure the distortion on the cylinder block upper face at some
different points in six directions (C), (D), (E), (F), (G) and (H) with a
straightedge (A) and a feeler gauge (B).
• If it exceeds the limit, replace cylinder block.
MAIN BEARING HOUSING INNER DIAMETER
• Install main bearing cap (2) without installing main bearings, and
tighten main bearing cap bolts to the specified torque. Refer to
107, "Disassembly and Assembly"
• Measure the inner diameter of main bearing housing with a bore
gauge.
• If out of the standard, replace cylinder block (1) and main bearing
cap as assembly.
NOTE:
Cylinder block cannot be replaced as a single part, because it is
machined together with main bearing cap.
PISTON TO CYLINDER BORE CLEARANCE
Cylinder Bore inner Diameter
• Using a bore gauge, measure cylinder bore for wear, out-of-round
and taper at six different points on each cylinder. [(A) and (B) direc-
tions at (C), (D) and (E)] is in longitudinal direction of engine.
• If the measured value exceeds the limit, or if there are scratches and/or seizure on the cylinder inner wall,
hone or re-bore the inner wall.
• Oversize piston is provided. When using oversize piston, re-bore cylinder so that the clearance of the piston-
to-cylinder bore satisfies the standard.
CAUTION:
When using oversize piston, use oversize pistons for all cylinders with oversize piston rings.
Piston Skirt Diameter
Limit
: Refer to
JPBIA0224ZZ
Standard
: Refer to
.
JPBIA0225ZZ
f
: 10 mm (0.39 in)
g
: 60 mm (2.36 in)
h
: 120 mm (4.72 in)
JPBIA2279ZZ
Wear limit:
Refer to
Out-of-round (Difference between “A” and “B”):
Taper limit (Difference between “C” and “E”):
Oversize (O/S)
: 0.2 mm (0.008 in)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст