Infiniti QX56 (Z62). Manual — part 394
DLK-42
< SYSTEM DESCRIPTION >
DIAGNOSIS SYSTEM (BCM)
SELF-DIAG RESULT
DATA MONITOR
AUTO LOCK SET
Auto door lock operation time can be changed in this mode
• MODE 1: OFF
• MODE 2: 30 sec
• MODE 3: 1 minute
• MODE 4: 2 minutes
• MODE 5: 3 minutes
• MODE 6: 4 minutes
• MODE 7: 5 minutes
HORN WITH KEYLESS LOCK
Horn reminder function mode by Intelligent Key button can be selected from the following with
this mode
• On: Operate
• Off: Non-operation
PW DOWN SET
Unlock button pressing time on Intelligent Key button can be selected from the following with
this mode
• MODE 1: 3 sec
• MODE 2: Non-operation
• MODE 3: 5 sec
WELCOME LIGHT SELECT
Welcome light function mode can be selected from the following with this mode
• Puddle/Outside Handle
• Room lamp
• Head & Tail Lamps (this item is displayed, but cannot be used)
• Heart Beat
WELCOME LIGHT OP SET
Welcome light function mode can be changed to operation with this mode
• On: Operate
• Off: Non-operation
Monitor item
Description
Monitor Item
Condition
REQ SW -DR
Indicates [On/Off] condition of door request switch (driver side)
REQ SW -AS
Indicates [On/Off] condition of door request switch (passenger side)
REQ SW -BD/TR
Indicates [On/Off] condition of back door request switch
PUSH SW
Indicates [On/Off] condition of push-button ignition switch
CLUTCH SW
NOTE:
This item is displayed, but cannot be monitored
BRAKE SW 1
Indicates [On/Off]* condition of stop lamp switch power supply
BRAKE SW 2
Indicates [On/Off] condition of stop lamp switch
DETE/CANCL SW
Indicates [On/Off] condition of P position
SFT PN/N SW
Indicates [On/Off] condition of P or N position
S/L -LOCK
Indicates [On/Off] condition of steering lock unit (LOCK)
S/L -UNLOCK
Indicates [On/Off] condition of steering lock unit (UNLOCK)
S/L RELAY -F/B
Indicates [On/Off] condition of steering lock relay
UNLK SEN -DR
Indicates [On/Off] condition of driver door UNLOCK status
PUSH SW -IPDM
Indicates [On/Off] condition of push-button ignition switch
IGN RLY1 -F/B
Indicates [On/Off] condition of ignition relay 1
DETE SW -IPDM
Indicates [On/Off] condition of P position
SFT PN -IPDM
Indicates [On/Off] condition of P or N position
SFT P -MET
Indicates [On/Off] condition of P position
SFT N -MET
Indicates [On/Off] condition of N position
ENGINE STATE
Indicates [Stop/Stall/Crank/Run] condition of engine states
DIAGNOSIS SYSTEM (BCM)
DLK-43
< SYSTEM DESCRIPTION >
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
*: OFF is displayed when brake pedal is depressed while brake switch power supply is OFF.
ACTIVE TEST
S/L LOCK-IPDM
Indicates [On/Off] condition of steering lock unit (LOCK)
S/L UNLK-IPDM
Indicates [On/Off] condition of steering lock unit (UNLOCK)
S/L RELAY-REQ
Indicates [On/Off] condition of steering lock relay
VEH SPEED 1
Display the vehicle speed signal received from combination meter by numerical value [Km/h]
VEH SPEED 2
Display the vehicle speed signal received from ABS or VDC or TCM by numerical value [Km/h]
DOOR STAT-DR
Indicates [LOCK/READY/UNLK] condition of unlock sensor
DOOR STAT-AS
Indicates [LOCK/READY/UNLK] condition of passenger side door status
ID OK FLAG
Indicates [Set/Reset] condition of key ID
PRMT ENG STRT
Indicates [Set/Reset] condition of engine start possibility
PRMT RKE STRT
NOTE:
This item is displayed, but cannot be monitored
TRNK/HAT MNTR
NOTE:
This item is displayed, but cannot be monitored
RKE-LOCK
Indicates [On/Off] condition of LOCK signal from Intelligent Key
RKE-UNLOCK
Indicates [On/Off] condition of UNLOCK signal from Intelligent Key
RKE-TR/BD
NOTE:
This item is displayed, but cannot be monitored
RKE-PANIC
Indicates [On/Off] condition of PANIC button of Intelligent Key
RKE-MODE CHG
Indicates [On/Off] condition of MODE CHANGE signal from Intelligent Key
RKE OPE COUN1
When remote keyless entry receiver receives the signal transmitted while operating on Intelli-
gent Key, the numerical value start changing
RKE OPE COUN2
NOTE:
This item is displayed, but cannot be monitored
Monitor Item
Condition
Test item
Description
BATTERY SAVER
This test is able to check interior room lamp operation
• On: Operate
• Off: Non-operation
OUTSIDE BUZZER
This test is able to check Intelligent Key warning buzzer operation
• On: Operate
• Off: Non-operation
INSIDE BUZZER
This test is able to check warning chime in combination meter operation
• Take Out: Take away warning chime sounds when CONSULT-III screen is touched
• Key: Key warning chime sounds when CONSULT-III screen is touched
• Knob: OFF position warning chime sounds when CONSULT-III screen is touched
• Off: Non-operation
INDICATOR
This test is able to check warning lamp operation
• KEY ON: “KEY” Warning lamp illuminates when CONSULT-III screen is touched
• KEY IND: “KEY” Warning lamp blinks when CONSULT-III screen is touched
• Off: Non-operation
INT LAMP
This test is able to check interior room lamp operation
• On: Operate
• Off: Non-operation
DLK-44
< SYSTEM DESCRIPTION >
DIAGNOSIS SYSTEM (BCM)
TRUNK
TRUNK : CONSULT-III Function (BCM - TRUNK)
INFOID:0000000006225857
DATA MONITOR
LCD
This test is able to check meter display information
• Engine start information displays when “BP N” on CONSULT-III screen is touched
• Engine start information displays when “BP I” on CONSULT-III screen is touched
• Key ID warning displays when “ID NG” on CONSULT-III screen is touched
• Steering lock information displays when “ROTAT” on CONSULT-III screen is touched
• P position warning displays when “SFT P” on CONSULT-III screen is touched
• INSRT: This item is displayed, but cannot be monitored
• BATT: This item is displayed, but cannot be monitored
• Take away through window warning displays when “NO KY” on CONSULT-III screen is
touched
• Take away warning display when “OUTKEY” on CONSULT-III screen is touched
• OFF position warning display when “LK WN” on CONSULT-III screen is touched
FLASHER
This test is able to check security hazard lamp operation
The hazard lamps are activated after “LH/RH/Off” on CONSULT-III screen is touched
P RANGE
This test is able to check A/T shift selector power supply
• On: Operate
• Off: Non-operation
ENGINE SW ILLUMI
This test is able to check push-button ignition switch illumination operation
Push-ignition switch illumination illuminates when “ON” on CONSULT-III screen is touched
LOCK INDICATOR
This test is able to check LOCK indicator (push-button ignition switch) operation
• On: Operate
• Off: Non-operation
ACC INDICATOR
This test is able to check ACC indicator (push-button ignition switch) operation
• On: Operate
• Off: Non-operation
IGNITION ON IND
This test is able to check ON indicator (push-button ignition switch) operation
• On: Operate
• Off: Non-operation
HORN
This test is able to check horn operation
• On: Operate
• Off: Non-operation
TRUNK/BACK DOOR
NOTE:
This item is displayed, but cannot be used
Test item
Description
Monitor Item
Contents
PUSH SW
Indicates [On/Off] condition of push switch
UNLK SEN -DR
Indicates [On/Off] condition of unlock sensor
VEH SPEED 1
Indicates [Km/h] condition of vehicle speed signal from combination meter
TR/BD OPEN SW
Indicates [On/Off] condition of back door opener switch
TRNK/HAT MNTR
NOTE:
This item is displayed, but cannot be monitored
RKE-TR/BD
NOTE:
This item is displayed, but cannot be monitored
DIAGNOSIS SYSTEM (AUTOMATIC BACK DOOR CONTROL UNIT)
DLK-45
< SYSTEM DESCRIPTION >
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
DIAGNOSIS SYSTEM (AUTOMATIC BACK DOOR CONTROL UNIT)
CONSULT-III Function (AUTOMATIC BACK DOOR CONTROL UNIT)
INFOID:0000000006225858
APPLICATION ITEM
CONSULT-III performs the following functions via CAN communication with automatic back door control unit.
DATA MONITOR
SELF-DIAG RESULT
Diagnosis mode
Function Description
Self Diagnostic Result
Displays the diagnosis results judged by automatic back door control unit
CAN Diag Support Monitor
Monitors the reception status of CAN communication viewed from automatic back door
control unit
Data Monitor
The automatic back door control unit input/output signals are displayed
Ecu Identification
The automatic back door control unit part number is displayed
Monitor Item
Unit
Description
VHCL SPEED MTR
[km/h]
Display the vehicle speed signal received from combination meter by nu-
merical value
VHCL SPEED ABS
[km/h]
Display the vehicle speed signal received from ABS actuator and electrical
unit by numerical value
VHCL SPEED SIG
[NORMAL/ER-
ROR]
Indicates condition of vehicle speed from automatic back door control unit
MAIN SW
[ON/OFF]
Indicates condition of automatic back door main switch
AUTO BD SW
[ON/OFF]
Indicates condition of automatic back door switch
BK DOOR CL SW
[ON/OFF]
Indicates condition of automatic back door close switch
UNLOCK SEN DR
[ON/OFF]
Indicates condition of unlock sensor
OPEN SW
[ON/OFF]
Indicates condition of open switch
CLOSE SW
[ON/OFF]
Indicates condition of close switch
HALF LATCH SW
[ON/OFF]
Indicates condition of half latch switch
TOUCH SEN RH
[ON/OFF/OPEN]
Indicates condition of touch sensor RH
TOUCH SEN LH
[ON/OFF/OPEN]
Indicates condition of touch sensor LH
P RANGE IND
[ON/OFF]
Indicates condition of P range signal from combination meter
RKE REQ
[OFF/MOVE/
REV]
Indicates condition of remote keyless entry signal from BCM
IGN SW
[ON/OFF]
Indicates condition of IGN power supply
ENCODER A
[LO/HI]
Indicates condition of encoder signal from encoder A
ENCODER B
[LO/HI]
Indicates condition of encoder signal from encoder B
BD OPENER SW
[ON/OFF]
Indicates condition of back door opener switch
UNLOCK SEN BD
[LOCK/
UNLOCK]
NOTE:
This item is displayed, but cannot be monitored
DESTINATION
[JPN/NAM]
Indicates specification of destination of the automatic back door system
HAZARD
[ON/OFF]
Indicates specification of hazard warning
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст