Infiniti QX56 (Z62). Manual — part 1143
SE-110
< REMOVAL AND INSTALLATION >
FRONT SEAT
16. Seat cushion trim
17. Seat cushion pad
18. Seat control unit
19. Seat cushion front finisher
20. Front inner slide cover
21. Front outer slide cover
22. Seat cushion climate controlled seat
duct finisher
23. Seat cushion thermal electric unit
24. Seat cushion climate controlled seat
hook (front)
25. Seat cushion climate controlled seat
duct
26. Seat cushion climate controlled seat
blower filter
27. Climate controlled seat cushion
blower motor
28. Seat cushion climate controlled seat
harness
29. Seat cushion climate controlled seat
hook (rear)
30. Seat cushion climate controlled seat
bracket
31. Climate controlled seat control unit
32. Seat cushion outer finisher
33. Seat slide and lifter switch knob
34. Seat reclining switch knob
35. Seat control switch
36. Lumber support switch
37. Seat control switch cover
38. Seat cushion outer finisher inside
(rear)
39. Seat cushion outer finisher inside
(front)
40. Seat harness
41. Rear outer slide cover
42. Seat cushion lower outer finisher
43. Side air bag module
44. Seatback board
45. Headrest display harness and upper
tube
46. Headrest display harness
47. Clip
48. Seatback climate controlled seat
duct
49. Climate controlled seatback blower
motor
50. Climate controlled seatback blower
motor bracket
51. Seatback climate controlled seat
blower filter
52. Seatback thermal electric unit
53. Seatback thermal electric unit brack-
et
54. Seatback climate controlled seat
duct finisher
55. Seat cushion lower inner finisher
56. Rear inner slide cover
57. Headrest display harness lower tube
58. Lumber support unit assembly
59. Seat frame assembly
: Pawl
: Metal clip
Refer to
for symbols in the figure.
FRONT SEAT
SE-111
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
SE
N
O
P
PASSENGER SEAT
JMJIA4579GB
1.
Headrest display
2.
Headrest display escutcheon
3.
Headrest trim
4.
Headrest pad and frame
5.
Headrest holder (locked)
6.
Headrest holder (free)
7.
Clip
8.
Headrest display harness and upper
tube
9.
Headrest display harness
10. Seatback board
11.
Side air bag module
12. Seatback climate controlled seat
duct
SE-112
< REMOVAL AND INSTALLATION >
FRONT SEAT
Removal and Installation
INFOID:0000000006217424
REMOVAL
CAUTION:
• When removing and installing, use shop cloths to protect parts from damage.
• When removing and installing, 2 workers are required so as to prevent it from dropping.
1.
Remove the front slide cover.
a.
Front outer slide cover
• Slide the seat to the rearmost position.
• Pull up the front edge of the front slide cover to release the
pawls.
• Slide the front slide cover forward to release the pawls.
13. Climate controlled seatback blower
motor
14. Climate controlled seatback blower
motor bracket
15. Seatback climate controlled seat
blower filter
16. Seatback thermal electric unit
17. Seat cushion lower outer finisher
18. Seatback climate controlled seat
duct finisher
19. Seatback thermal electric unit brack-
et
20. Seat cushion lower inner finisher
21. Rear inner slide cover
22. Rear outer slide cover
23. Seat harness
24. Seat cushion outer finisher inside
(front)
25. Seat cushion outer finisher inside
(rear)
26. Lumber support switch
27. Seat control switch cover
28. Seat control switch
29. Seat cushion outer finisher
30. Seat reclining switch knob
31. Seat slide and lifter switch knob
32. Climate controlled seat control unit
33. Seat cushion climate controlled seat
harness
34. Seat cushion climate controlled seat
hook (rear)
35. Seat cushion climate controlled seat
bracket
36. Climate controlled seat cushion
blower motor
37. Seat cushion climate controlled seat
hook (front)
38. Seat cushion climate controlled seat
duct
39. Seat cushion thermal electric unit
40. Seat cushion climate controlled seat
duct finisher
41. Seat cushion climate controlled seat
blower filter
42. Occupant detection system control
unit
43. Front outer slide cover
44. Front inner slide cover
45. Seat cushion front finisher
46. Seat cushion pad
47. Seat cushion trim
48. Seat cushion inner finisher
49. Seat cushion inner finisher inside
(front)
50. Seat cushion inner finisher inside
(rear)
51. Anchor bolt
52. Seat belt buckle pre-tensioner
53. Foot welcome lamp
54. Seatback pad
55. Seatback trim
56. Seatback silencer
57. Headrest display harness lower tube
58. Lumber support unit assembly
59. Seat frame assembly
: Pawl
: Metal clip
Refer to
for symbols in the figure.
: Pawl
JMJIA3824ZZ
FRONT SEAT
SE-113
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
SE
N
O
P
b.
Front inner slide cover
• Slide the seat to the rearmost position.
• Pull up the front edge of the front slide cover to release the
pawls.
• Slide the front slide cover forward to release the pawls.
2.
Remove the mounting bolts on the front side of the front seat.
3.
Remove the rear slide cover.
a.
Rear inner slide cover
• Slide the seat to the foremost position.
• Pull up the rear edge of the rear inner slide cover to release
the pawls.
• Slide the rear inner slide cover rearward to release the pawls.
b.
Rear outer slide cover
• Slide the seat to the foremost position.
• Pull up the rear edge of the rear outer slide cover to release
the pawls.
• Slide the rear outer slide cover rearward to release the pawls.
4.
Remove the mounting bolts on the rear side of the front seat.
5.
Set seatback in a standing position.
6.
Slide the seat to the rearmost position.
7.
Disconnect harness connectors under the seat and remove harness securing clips.
CAUTION:
Before removal, turn ignition switch OFF, disconnect battery negative terminal and then wait for at
least 3 minutes or more.
8.
Remove seat from the vehicle.
CAUTION:
When removing and installing, use shop cloths to protect parts from damage.
INSTALLATION
Note the following items, and then install in the reverse order of removal.
CAUTION:
• Before installation, turn ignition switch OFF, disconnect battery negative terminal and then wait for
at least 3 minutes or more.
• Clamp the harness in position.
NOTE:
After installing the front seat, perform additional service when removing battery negative terminal. Refer to
ADP-51, "ADDITIONAL SERVICE WHEN REMOVING BATTERY NEGATIVE TERMINAL : Description"
: Pawl
JMJIA3823ZZ
: Pawl
JMJIA3826ZZ
: Pawl
JMJIA3825ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст