Infiniti QX56 (Z62). Manual — part 180
REPLACEMENT OPERATIONS
BRM-47
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
BRM
N
O
P
Create the reinforcing sheet from the redundant area of service parts for butt welding area. Weld the
reinforcing sheet on the back of butt welding area, and then perform butt welding.
After welding, apply anti-corrosive wax on the reinforcing sheet-welded area.
View A and B: Before installing outer front side member
1.
Reinforcing sheet
Unit: mm (in)
: Vehicle front
Replacement parts
z
Front side member assembly (LH)
JSKIA2096GB
BRM-48
< SERVICE DATA AND SPECIFICATIONS (SDS)
BODY ALIGNMENT
SERVICE DATA AND SPECIFICATIONS (SDS)
BODY ALIGNMENT
Body Center Marks
INFOID:0000000006248507
A mark is placed on each part of the body to indicate the vehicle center. When repairing the vehicle frame
(members, pillars, etc.) damaged by an accident which it enables more accurate and effective repair by using
these marks together with body alignment specifications.
Unit: mm (in)
Description
INFOID:0000000006248508
• All dimensions indicated in the figures are actual.
• When using a tracking gauge, adjust both pointers to equal length. Then check the pointers and gauge itself
to make sure there is no free play.
: Vehicle front
Points
Portion
Marks
A
Upper dash
Hole 7
×
12 (0.28
×
0.47)
B
Cowl top
Embossment
C
Rear roof
Indent
JSKIA1895ZZ
BODY ALIGNMENT
BRM-49
< SERVICE DATA AND SPECIFICATIONS (SDS)
C
D
E
F
G
H
I
J
L
M
A
B
BRM
N
O
P
• When a measuring tape is used, check to be sure there is no elongation, twisting or bending.
• Measurements should be taken at the center of the mounting holes.
• An asterisk (*) following the value at the measuring point indicates that the measuring point on the other side
is symmetrically the same value.
• The coordinates of the measurement points are the distances measured from the standard line of
″
X
″
,
″
Y
″
and
″
Z
″
.
•
″
Z
″
: Imaginary base line [300 mm (11.81 in) below datum line (
″
0Z
″
at design plan)]
Engine Compartment
INFOID:0000000006248509
Measurement
Dimensions marked with
″
*
″
indicate symmetrically identical dimensions on both the right and left hand of the
vehicle.
1.
Vehicle center
2.
Front axle center
3.
Imaginary base line
JSKIA0073GB
BRM-50
< SERVICE DATA AND SPECIFICATIONS (SDS)
BODY ALIGNMENT
«The others»
Unit: mm (in)
Measurement Points
Unit: mm (in)
Point
Dimension
Memo
Point
Dimension
Memo
Point
Dimension
Memo
Point
Dimension
Memo
A - C
865 (34.06)*
C - M
897 (35.31)*
F - m
1467 (57.76)*
N - o
1078 (42.44)*
A - D
871 (34.29)*
C - m
1635 (64.37)*
G - g
1608 (63.31)
N - p
1117 (43.98)*
A - F
821 (32.32)*
D - d
1719 (67.68)
G - j
1614 (63.54)*
N - Q
397 (15.63)*
A - H
938 (36.93)*
E - M
625 (24.61)*
G - M
613 (24.13)*
O - o
1077 (42.40)
A - K
1013 (39.88)*
E - m
1320 (51.97)*
G - m
1457 (57.36)*
O - P
322 (12.68)*
B - G
453 (17.83)*
F - f
1588 (62.52)
H - h
1657 (65.24)
O - p
1108 (43.62)*
B - g
1740 (68.50)*
F - J
257 (10.12)*
J - M
427 (16.81)*
O - q
1123 (44.21)*
B - j
1798 (70.79)*
F - j
1611 (63.43)*
J - m
1383 (54.45)*
P - p
1044 (41.10)
C - c
1720 (67.72)
F - M
652 (25.67)*
K - k
1600 (62.99)
P - q
1045 (41.14)*
JSKIA1946GB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст