Infiniti QX56 (Z62). Manual — part 357
DAS
DIAGNOSIS AND REPAIR WORK FLOW
DAS-465
< BASIC INSPECTION >
[BSW]
C
D
E
F
G
H
I
J
K
L
M
B
N
P
A
NO
>> INSPECTION END
DAS-466
< BASIC INSPECTION >
[BSW]
PRE-INSPECTION FOR DIAGNOSIS
PRE-INSPECTION FOR DIAGNOSIS
Inspection Procedure
INFOID:0000000006223875
1.
CHECK REAR BUMPER NEAR THE SIDE RADAR
Are rear bumper near the side radar contaminated with foreign materials?
YES
>> Clean the rear bumper.
NO
>> GO TO 2.
2.
CHECK SIDE RADAR AND THE SIDE RADAR OUTSKIRTS
Are side radar and the side radar outskirts contaminated with foreign materials?
YES
>> Clean the side radar or side radar outskirts.
NO
>> GO TO 3.
3.
CHECK SIDE RADAR INSTALLATION CONDITION
Check side radar installation condition (installation position, properly tightened, a bent bracket).
Is it properly installed?
YES
>> INSPECTION END
NO
>> Install side radar properly.
DAS
ADDITIONAL SERVICE WHEN REPLACING SIDE RADAR
DAS-467
< BASIC INSPECTION >
[BSW]
C
D
E
F
G
H
I
J
K
L
M
B
N
P
A
ADDITIONAL SERVICE WHEN REPLACING SIDE RADAR
Description
INFOID:0000000006223876
• After replacing the side radar, activate (normal usage mode) it in work support mode with CONSLUT-III.
• If both side radars are not brought into the normal usage mode, BSW does not operate and the BSW warn-
ing lamp blinks.
Work Procedure
INFOID:0000000006223877
1.
ACTIVATE OPERATION
1.
Select “WORK SUPPORT” item “ACTIVATE OPERATION” of SIDE RADAR (LEFT, RIGHT) with CON-
SULT-III.
2.
Select “Activate”.
3.
Check that “DATA MONITOR” item “ACTIVATE OPE” is changed to “On”.
4.
Turn ignition switch OFF.
>> GO TO 2.
2.
PERFORM SELF-DIAGNOSIS
1.
Turn ignition switch ON.
2.
Perform the self-diagnosis of side radar with CONSULT-III. Check if any DTC is detected.
Is any DTC detected?
YES
>> Perform the trouble diagnosis for the detected DTC. Refer to
NO
>> GO TO 3.
3.
BSW WARNING LAMP CHECK
1.
Perform the BSW system action test. Refer to
.
2.
Check that BSW system operates normally.
>> WORK END
DAS-468
< BASIC INSPECTION >
[BSW]
ACTION TEST
ACTION TEST
Description
INFOID:0000000006223878
Always perform the BSW system action test to check that the system operates normally after replacing the
side radar LH/RH, or repairing any BSW system malfunction.
WARNING:
Be careful of traffic conditions and safety around the vehicle when performing road test.
CAUTION:
Fully understand the following items well before the road test;
• Precautions: Refer to
DAS-407, "Precaution for BSW System Service"
.
• System description: Refer to
• Normal operating condition: Refer to
Work Procedure
INFOID:0000000006223879
WARNING:
Be careful of traffic conditions and safety around the vehicle when performing road test.
CAUTION:
Fully understand the following items well before the road test;
• Precautions: Refer to
DAS-407, "Precaution for BSW System Service"
.
• System description: Refer to
• Normal operating condition: Refer to
1.
BSW SYSTEM ACTION TEST
1.
Drive the vehicle.
2.
Turn warning systems switch ON (warning systems ON indicator is ON).
3.
Check BSW operation according to the following table.
Vehicle condition/ Driver's operation
Action
Warning
systems ON
indicator
Vehicle speed
(Approx.)
[km/h (MPH)]
Turn signal
condition
Status of ve-
hicle detec-
tion within
detection
area
Indication on the
BSW indicator
Buzzer
OFF
—
—
—
OFF
OFF
ON
Less than ap-
prox.
29 (18)
—
—
OFF
OFF
Approx.
32 (20)
or more
—
Vehicle is
absent
OFF
OFF
OFF
Vehicle is
detected
ON
OFF
ON
(vehicle de-
tected direc-
tion)
Before turn
signal oper-
ates
Vehicle is
detected
Blink
Short continuous beep
Vehicle is
detected af-
ter turn sig-
nal operates
Blink
OFF
JSOIA0251GB
JSOIA0252GB
JSOIA0251GB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст