Infiniti QX56 (Z62). Manual — part 429
DLK-182
< SYMPTOM DIAGNOSIS >
P RANGE INTERLOCK DOOR LOCK/UNLOCK FUNCTION DOES NOT OPER-
ATE
P RANGE INTERLOCK DOOR LOCK/UNLOCK FUNCTION DOES NOT OP-
ERATE
Diagnosis Procedure
INFOID:0000000006226020
1.
CHECK “AUTOMATIC LOCK/UNLOCK SELECT” SETTING IN “WORK SUPPORT”
1.
Select “DOOR LOCK” of “BCM” using CONSULT-III.
2.
Select “AUTOMATIC LOCK/UNLOCK SELECT” in “WORK SUPPORT” mode.
3.
Check “AUTOMATIC LOCK/UNLOCK SELECT” setting in “WORK SUPPORT”.
Refer to
DLK-39, "DOOR LOCK : CONSULT-III Function (BCM - DOOR LOCK)"
.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Set “Unlock Only”, “Lock Only” or “Lock/Unlock” in “AUTOMATIC LOCK/UNLOCK SELECT”.
2.
CHECK “AUTOMATIC DOOR LOCK SELECT” SETTING IN “WORK SUPPORT”
1.
Select “DOOR LOCK” of “BCM” using CONSULT-III.
2.
Select “AUTOMATIC DOOR LOCK SELECT” in “WORK SUPPORT” mode.
3.
Check “AUTOMATIC DOOR LOCK SELECT” setting in “WORK SUPPORT”.
Refer to
DLK-39, "DOOR LOCK : CONSULT-III Function (BCM - DOOR LOCK)"
.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Set “P RANGE” in “AUTOMATIC DOOR LOCK SELECT”.
3.
CHECK “AUTOMATIC DOOR UNLOCK SELECT” SETTING IN “WORK SUPPORT”
1.
Select “DOOR LOCK” of “BCM” using CONSULT-III.
2.
Select “AUTOMATIC DOOR UNLOCK SELECT” in “WORK SUPPORT” mode.
3.
Check “AUTOMATIC DOOR UNLOCK SELECT” setting in “WORK SUPPORT”.
Refer to
DLK-39, "DOOR LOCK : CONSULT-III Function (BCM - DOOR LOCK)"
.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Set “MODE 2” or “MODE 4” in “AUTOMATIC DOOR UNLOCK SELECT”.
4.
REPLACE BCM
• Replace BCM. Refer to
BCS-81, "Removal and Installation"
.
• Confirm the operation after replacement.
Is the result normal?
YES
>> INSPECTION END
NO
>> Check intermittent incident. Refer to
GI-40, "Intermittent Incident"
.
HAZARD AND HORN REMINDER DOES NOT OPERATE
DLK-183
< SYMPTOM DIAGNOSIS >
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
HAZARD AND HORN REMINDER DOES NOT OPERATE
Diagnosis Procedure
INFOID:0000000006226021
1.
CHECK “HAZARD ANSWER BACK” SETTING IN “WORK SUPPORT”
1.
Select “INTELLIGENT KEY” of “BCM” using CONSULT-III.
2.
Select “HAZARD ANSWER BACK” in “WORK SUPPORT” mode.
3.
Check the “HAZARD ANSWER BACK” setting in “WORK SUPPORT”.
Refer to
DLK-41, "INTELLIGENT KEY : CONSULT-III Function (BCM - INTELLIGENT KEY)"
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Set the “Lock Only”, “Unlock Only” or “Lock/Unlock” in “HAZARD ANSWER BACK”.
2.
CHECK “HORN WITH KEYLESS LOCK” SETTING IN “WORK SUPPORT”
1.
Select “INTELLIGENT KEY” of “BCM” using CONSULT-III.
2.
Select “HORN WITH KEYLESS LOCK” in “WORK SUPPORT” mode.
3.
Check the “HORN WITH KEYLESS LOCK” in “WORK SUPPORT”.
Refer to
DLK-41, "INTELLIGENT KEY : CONSULT-III Function (BCM - INTELLIGENT KEY)"
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Set the “On” in “HORN WITH KEYLESS LOCK”.
3.
CHECK HAZARD FUNCTION
Check hazard function.
Refer to
DLK-149, "Component Function Check"
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace the malfunctioning parts.
4.
CHECK HORN FUNCTION
Check horn function.
Refer to
SEC-143, "Component Function Check"
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Repair or replace the malfunctioning parts.
5.
REPLACE BCM
• Replace BCM. Refer to
BCS-81, "Removal and Installation"
.
• Confirm the operation after replacement.
Is the result normal?
YES
>> INSPECTION END
NO
>> Check intermittent incident. Refer to
GI-40, "Intermittent Incident"
.
DLK-184
< SYMPTOM DIAGNOSIS >
HAZARD AND BUZZER REMINDER DOES NOT OPERATE
HAZARD AND BUZZER REMINDER DOES NOT OPERATE
Diagnosis Procedure
INFOID:0000000006226022
1.
CHECK “HAZARD ANSWER BACK” SETTING IN “WORK SUPPORT”
1.
Select “INTELLIGENT KEY” of “BCM” using CONSULT-III.
2.
Select “HAZARD ANSWER BACK” in “WORK SUPPORT” mode.
3.
Check the “HAZARD ANSWER BACK” setting in “WORK SUPPORT”.
Refer to
DLK-41, "INTELLIGENT KEY : CONSULT-III Function (BCM - INTELLIGENT KEY)"
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Set the “Lock Only”, “Unlock Only” or “Lock/Unlock” in “HAZARD ANSWER BACK”.
2.
CHECK “ANS BACK I-KEY LOCK” SETTING IN “WORK SUPPORT”
1.
Select “INTELLIGENT KEY” of “BCM” using CONSULT-III.
2.
Select “ANS BACK I-KEY LOCK” in “WORK SUPPORT” mode.
3.
Check the “ANS BACK I-KEY LOCK”setting in “WORK SUPPORT”.
Refer to
DLK-41, "INTELLIGENT KEY : CONSULT-III Function (BCM - INTELLIGENT KEY)"
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Set the “Horn Chirp” or “Buzzer” in “ANS BACK I-KEY LOCK”.
3.
CHECK “ANS BACK I-KEY UNLOCK” SETTING IN “WORK SUPPORT”
1.
Select “INTELLIGENT KEY” of “BCM” using CONSULT-III.
2.
Select “ANS BACK I-KEY UNLOCK” in “WORK SUPPORT” mode.
3.
Check the “ANS BACK I-KEY UNLOCK” setting in “WORK SUPPORT”.
Refer to
DLK-41, "INTELLIGENT KEY : CONSULT-III Function (BCM - INTELLIGENT KEY)"
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Set the “On” in “ANS BACK I-KEY UNLOCK”.
4.
CHECK HAZARD FUNCTION
Check hazard function.
Refer to
DLK-149, "Component Function Check"
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Repair or replace the malfunctioning parts.
5.
CHECK INTELLIGENT KEY WARNING BUZZER
Check Intelligent Key warning buzzer.
Refer to
DLK-143, "Component Function Check"
Is the inspection result normal?
YES
>> GO TO 6.
NO
>> Repair or replace the malfunctioning parts.
6.
REPLACE BCM
• Replace BCM. Refer to
BCS-81, "Removal and Installation"
.
• Confirm the operation after replacement.
Is the result normal?
YES
>> INSPECTION END
NO
>> Check intermittent incident. Refer to
GI-40, "Intermittent Incident"
.
KEY REMINDER FUNCTION DOES NOT OPERATE
DLK-185
< SYMPTOM DIAGNOSIS >
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
KEY REMINDER FUNCTION DOES NOT OPERATE
Diagnosis Procedure
INFOID:0000000006226023
1.
CHECK “ANTI KEY LOCK IN FUNCTI” SETTING IN “WORK SUPPORT”
1.
Select “INTELLIGENT KEY” of “BCM” using CONSULT-III.
2.
Select “ANTI KEY LOCK IN FUNCTI” in “WORK SUPPORT” mode.
3.
Check “ANTI KEY LOCK IN FUNCTI” setting in “WORK SUPPORT”.
Refer to
DLK-41, "INTELLIGENT KEY : CONSULT-III Function (BCM - INTELLIGENT KEY)"
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Set “On” in “ANTI KEY LOCK IN FUNCTI”.
2.
CHECK INSIDE KEY ANTENNA
Check inside key antenna.
• Instrument center: Refer to
.
.
• Luggage room: Refer to
.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace the malfunctioning parts.
3.
CHECK UNLOCK SENSOR
Check unlock sensor.
Refer to
DLK-130, "Component Function Check"
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace the malfunctioning parts.
4.
REPLACE BCM
• Replace BCM. Refer to
BCS-81, "Removal and Installation"
.
• Confirm the operation after replacement.
Is the result normal?
YES
>> INSPECTION END
NO
>> Check intermittent incident. Refer to
GI-40, "Intermittent Incident"
.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст