Infiniti QX56 (Z62). Manual — part 1097
CHECK SHOCK ABSORBER FOR MALFUNCTION
SCS-25
< BASIC INSPECTION >
[HBMC]
C
D
F
G
H
I
J
K
L
M
A
B
SCS
N
O
P
- Disconnect upper side pipe (B) of front shock absorber.
• For rear shock absorber
- Disconnect lower side pipe (B) of rear shock absorber.
9.
Install a leak check plug (SST: KV40108400) (A) to the removed
pipe and tighten the leak check plug to the specified torque.
CAUTION:
• O-ring must be free of scratches and damage.
• Piping must be kept free of the intrusion of dust and dirt.
10. Loosen lock nuts of needle valves B and D of PPMU and then
tighten needle valves B and D.
11. Loosening position of needle valve of PPMU varies according to
shock absorber that is checked. Loosen needle valve of PPMU
by approximately 2 rotations, as per the following table.
CAUTION:
Never loosen the needle valve more than required.
12. Set knob (A) of suspension oil pump to the direction as shown in
the figure.
13. Apply pressure of up to 2.4 MPa.
14. Go to step 15 when oil comes out from lower portion of shock
absorber which pipe is removed from. Go to step 16 when oil
does not come out.
15. Replace shock absorber, since shock absorber has internal
FSU-10, "Removal and Installation"
(front),
RSU-8, "Removal and Installation"
A
: Lower side pipe
JSEIA0233ZZ
A
: Upper side pipe
JSEIA0203ZZ
Tightening torque
: 5.0 N·m (0.51 kg-m, 44 in-lb)
Shock absorber
Loosening position of needle valve
Front LH
C
Rear LH
C
Front RH
A
Rear RH
A
JSEIA0210ZZ
JSEIA0191ZZ
SCS-26
< BASIC INSPECTION >
[HBMC]
CHECK SHOCK ABSORBER FOR MALFUNCTION
16. Shock absorber that is checked is normal. Set knob (A) of sus-
pension oil pump to the direction as shown in the figure and
check that reading of pressure gauge is 0 MPa.
17. Tighten the loosened needle valve of PPMU.
18. Remove leak check plug from pipe. Install pipe to lower portion
of shock absorber and tighten pipe to the specified torque.
CAUTION:
• O-ring must be free of scratches and damage.
• Piping must be kept free of the intrusion of dust and dirt.
19. Check other shock absorbers in accordance with procedures of steps 8 to 18.
20. Tighten needle valves A, C, and E of PPMU to the specified torque, after completion of check.
21. Loosen needle valves B and D of PPMU by approximately 2 rotations and then tighten lock nuts to the
specified torque.
CAUTION:
Never loosen the needle valve more than required.
Tightening torque
: 5.0 N·m (0.51 kg-m, 44 in-lb)
Tightening torque
: 8.3 N·m (0.85 kg-m, 73 in-lb)
Tightening torque
: 20 N·m (2.0 kg-m, 15 ft-lb)
JSEIA0193ZZ
CHECK ORIFICE FOR CLOGGING
SCS-27
< BASIC INSPECTION >
[HBMC]
C
D
F
G
H
I
J
K
L
M
A
B
SCS
N
O
P
CHECK ORIFICE FOR CLOGGING
Work Procedure
INFOID:0000000006256015
CAUTION:
• Clean surrounding areas of oil injection jack using steam before starting operation, since there may
be mud on it.
• Clean oil pressure gauge (special service tool: KV40108000) jack with steam before use.
1.
Remove protector of PPMU.
2.
Remove cap of oil injection jack.
3.
Install an oil pressure gauge (SST: KV40108000) (A) to oil injec-
tion jack.
CAUTION:
• Jack must be securely inserted until a click sound can be
heard.
• Pressure reducing valve (B) of the oil pressure gauge
must be closed.
4.
Loosen needle valves A, C, and E of PPMU by approximately 2
rotations.
CAUTION:
Never loosen the needle valve more than required.
5.
Lift up the vehicle.
CAUTION:
Check that tires never contact the ground.
6.
Tighten needle valves A, C, and E of PPMU.
7.
Lift down the vehicle.
CAUTION:
Check that the lift is fully lowered.
8.
Loosen pressure reducing valve (A) of oil pressure gauge and
then lower pressure.
CAUTION:
Be careful since oil drains swiftly from oil drain hole (B).
9.
Check that reading of oil pressure gauge is 0 MPa. Close pres-
sure reducing valve.
10. Loosen needle valve E of PPMU by approximately 2 rotations.
CAUTION:
Never loosen the needle valve more than required.
11. Write down a value of the oil pressure gauge.
12. Tighten needle valve E of PPMU.
13. Loosen pressure reducing valve of oil pressure gauge and then lower pressure.
CAUTION:
Be careful since oil drains swiftly from oil drain hole.
14. Check that reading of oil pressure gauge is 0 MPa. Close pressure reducing valve.
15. Loosen needle valve A of PPMU by approximately 2 rotations.
CAUTION:
Never loosen the needle valve more than required.
16. Read a value of the oil pressure gauge after 5 minutes.
17. Compare difference of reading with pressure reading in step 11.
JSEIA0186ZZ
JSEIA0187ZZ
JSEIA0188ZZ
SCS-28
< BASIC INSPECTION >
[HBMC]
CHECK ORIFICE FOR CLOGGING
18. Tighten needle valve A of PPMU.
19. Loosen pressure reducing valve of oil pressure gauge and then lower pressure.
CAUTION:
Be careful since oil drains swiftly from oil drain hole.
20. Check that reading of oil pressure gauge is 0 MPa. Close pressure reducing valve.
21. Loosen needle valve C of PPMU by approximately 2 rotations.
CAUTION:
Never loosen the needle valve more than required.
22. Read a value of the oil pressure gauge after 5 minutes.
23. Compare difference of reading with pressure reading in step 11.
24. Tighten needle valve C of PPMU.
25. Loosen pressure reducing valve of oil pressure gauge and then lower pressure.
CAUTION:
Be careful since oil drains swiftly from oil drain hole.
26. Check that reading of oil pressure gauge is 0 MPa.
27. Remove oil pressure gauge.
28. Tighten needle valves A, C, and E of PPMU to the specified torque.
Pressure difference
0.2 MPa or more
: Replace the PPMU. Refer to
MIDDLE TUBE ASSEMBLY, PPMU PIPE : Removal
and Installation"
.
0.2 MPa or less
: Normal
Pressure difference
0.2 MPa or more
: Replace the PPMU. Refer to
MIDDLE TUBE ASSEMBLY, PPMU PIPE : Remov-
al and Installation"
0.2 MPa or less
: Normal
: 8.3 N·m (0.85 kg-m, 73 in-lb)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст