Infiniti QX56 (Z62). Manual — part 416
DLK-130
< DTC/CIRCUIT DIAGNOSIS >
UNLOCK SENSOR
UNLOCK SENSOR
Component Function Check
INFOID:0000000006225941
1.
CHECK FUNCTION
1.
Select “INTELLIGENT KEY” of “BCM” using CONSULT-III.
2.
Select “UNLK SEN-DR” in “DATA MONITOR” mode.
3.
Check that the function operates normally according to the following conditions.
Is the inspection result normal?
YES
>> Unlock sensor is OK.
NO
>> Refer to
DLK-130, "Diagnosis Procedure"
.
Diagnosis Procedure
INFOID:0000000006225942
1.
CHECK UNLOCK SENSOR INPUT SIGNAL
1.
Turn ignition switch OFF.
2.
Disconnect front door lock assembly (driver side) connector.
3.
Check signal between front door lock assembly (driver side) harness connector and ground with oscillo-
scope.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> GO TO 2.
2.
CHECK UNLOCK SENSOR CIRCUIT
1.
Disconnect BCM connector.
2.
Check continuity between BCM harness connector and front door lock assembly (driver side) harness
connector.
3.
Check continuity between BCM harness connector and ground.
Is the inspection result normal?
YES
>> Replace BCM. Refer to
BCS-81, "Removal and Installation"
Monitor item
Condition
Status
UNLK SEN -DR
Driver side door
Lock
OFF
Unlock
ON
(+)
(–)
Signal
(Reference value)
Front door lock assembly (driver side)
Connector
Terminal
D9
3
Ground
PKIB4960J
BCM
Front door lock assembly (driver side)
Continuity
Connector
Terminal
Connector
Terminal
M68
31
D9
3
Existed
BCM
Ground
Continuity
Connector
Terminal
M68
31
Not existed
UNLOCK SENSOR
DLK-131
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
NO
>> Repair or replace harness.
3.
CHECK UNLOCK SENSOR GROUND CIRCUIT
Check continuity between front door lock assembly (driver side) harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace harness.
4.
CHECK UNLOCK SENSOR
DLK-131, "Component Inspection"
.
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Replace front door lock assembly (driver side).
5.
CHECK INTERMITTENT INCIDENT
GI-40, "Intermittent Incident"
.
>> INSPECTION END
Component Inspection
INFOID:0000000006225943
1.
CHECK UNLOCK SENSOR
1.
Turn ignition switch OFF.
2.
Disconnect front door lock assembly (driver side) connector.
3.
Check continuity between front door lock assembly (driver side) terminals.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Replace front door lock assembly (driver side).
Front door lock assembly (driver side)
Ground
Continuity
Connector
Terminal
D9
4
Existed
Front door lock assembly (driver side)
Condition
Continuity
Terminal
3
4
Driver side door
Unlock
Existed
Lock
Not existed
DLK-132
< DTC/CIRCUIT DIAGNOSIS >
DOOR KEY CYLINDER SWITCH
DOOR KEY CYLINDER SWITCH
Component Function Check
INFOID:0000000006225944
1.
CHECK FUNCTION
1.
Select “DOOR LOCK” of “BCM” using CONSULT-III.
2.
Select “KEY CYL LK-SW”, “KEY CYL UN-SW” in “DATA MONITOR” mode.
3.
Check that the function operates normally according to the following conditions.
Is the inspection result normal?
YES
>> Door key cylinder switch is OK.
NO
>> Refer to
DLK-132, "Diagnosis Procedure"
.
Diagnosis Procedure
INFOID:0000000006225945
1.
CHECK DOOR KEY CYLINDER SWITCH INPUT SIGNAL
1.
Turn ignition switch OFF.
2.
Disconnect front door lock assembly (driver side) connector.
3.
Check voltage between front door lock assembly (driver side) harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> GO TO 2.
2.
CHECK DOOR KEY CYLINDER SWITCH SIGNAL CIRCUIT
1.
Disconnect power window main switch connector.
2.
Check continuity between power window main switch harness connector and front door lock assembly
(driver side) harness connector.
3.
Check continuity between power window main switch harness connector and ground.
Is the inspection result normal?
YES
>> Replace power window main switch. Refer to
PWC-74, "Removal and Installation"
Monitor item
Condition
Status
KEY CYL LK-SW
Driver side door key cylinder
Lock
ON
Neutral / Unlock
OFF
KEY CYL UN-SW
Unlock
ON
Neutral / Lock
OFF
(+)
(–)
Voltage
(Approx.)
Front door lock assembly (driver side)
Connector
Terminal
D9
5
Ground
5 V
6
Power window main switch
Front door lock assembly (driver side)
Continuity
Connector
Terminal
Connector
Terminal
D5
4
D9
6
Existed
6
5
Power window main switch
Ground
Continuity
Connector
Terminal
D5
4
Not existed
6
DOOR KEY CYLINDER SWITCH
DLK-133
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
NO
>> Repair or replace harness.
3.
CHECK DOOR KEY CYLINDER SWITCH GROUND CIRCUIT
Check continuity between front door lock assembly (driver side) harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace harness.
4.
CHECK DOOR KEY CYLINDER SWITCH
DLK-133, "Component Inspection"
.
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Replace front door lock assembly (driver side).
5.
CHECK INTERMITTENT INCIDENT
GI-40, "Intermittent Incident"
.
>> INSPECTION END
Component Inspection
INFOID:0000000006225946
1.
CHECK DOOR KEY CYLINDER SWITCH
1.
Turn ignition switch OFF.
2.
Disconnect front door lock assembly (driver side) connector.
3.
Check continuity between front door lock assembly (driver side) terminals.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Replace front door lock assembly (driver side).
Front door lock assembly (driver side)
Ground
Continuity
Connector
Terminal
D9
4
Existed
Front door lock assembly (driver side)
Condition
Continuity
Terminal
5
4
Driver side door key cylinder
Unlock
Existed
Neutral / Lock
Not existed
6
Lock
Existed
Neutral / Unlock
Not existed
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст