Infiniti QX56 (Z62). Manual — part 761
GW-12
< REMOVAL AND INSTALLATION >
WINDSHIELD GLASS
Removal and Installation
INFOID:0000000006220814
REMOVAL
1.
Remove front pillar garnish (LH and RH). Refer to
INT-14, "Removal and Installation"
2.
Remove partially headlining (front edge). Refer to
INT-29, "Removal and Installation"
.
3.
Disconnect inside mirror harness connector.
4.
Remove rain sensor cover and then disconnect rain sensor harness connector. Refer to
5.
Remove drip molding. Refer to
EXT-43, "Removal and Installation"
.
6.
Remove windshield molding upper using pliers. Refer to
.
7.
Remove front wiper arm (LH and RH). Refer to
WW-66, "Removal and Installation"
8.
Remove cowl top cover. Refer to
EXT-21, "Removal and Installation"
.
9.
Remove front fender cover (LH and RH). Refer to
.
10. Disconnect wiper deicer harness connector (with wiper deicer).
11. Remove front pillar finisher (LH and RH). Refer to
EXT-40, "Removal and Installation"
.
12. Apply protective tape around the windshield glass to protect the painted surface from damage.
13. Remove glass using piano wire or power cutting tool (A) and an inflatable pump bag (B).
NOTE:
Mark the body and the glass with matching marks if the windshield glass is reused.
WARNING:
Always wear safety glasses and heavy gloves to prevent injury.
CAUTION:
• Never use a cutting knife or power cutting tool when the windshield glass is reused.
• Be careful not to scratch the glass when removing.
• Never set or stand the glass on its edge. Small chips may develop into cracks.
INSTALLATION
• The dam sealant rubber and insulator should be installed in position.
• Use a genuine Nissan Urethane Adhesive Kit (if available) or an equivalent and follow the instructions pro-
vided with it.
• Open a door window while the urethane adhesive is curing. This prevents the glass from being forced out by
passenger room air pressure when all door windows are closed.
• The molding must be installed securely so that it is in position and leaves no clearance.
• Inform the customer that the vehicle should remain stationary until the urethane adhesive has completely
cured (approximately 24 hours). Curing time varies with temperature and humidity.
WARNING:
• Keep heat and open flames away as primers and adhesive are flammable.
• The materials contained in the kit are harmful if swallowed, and may irritate skin and eyes. Never let
them come in contact with the skin and eyes.
• Use in an open, well ventilated location. Never breathe the vapors. They may be harmful if inhaled.
Move immediately to an area with fresh air if affected by vapor inhalation.
• Driving the vehicle before the urethane adhesive has completely cured may affect the performance
of the windshield in case of an accident.
CAUTION:
• Perform adjustment of front wiper arms stop location. Refer to
.
PIIB5779E
WINDSHIELD GLASS
GW-13
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
GW
N
O
P
• Never use an adhesive which is past its usable term. Shelf life of this product is limited to six months
after the date of manufacture. Carefully adhere to the expiration or manufacture date printed on the
box.
• Keep primers and adhesive in a cool, dry place. Ideally, they should be stored in a refrigerator.
• Never leave primers or adhesive cartridge unattended with their caps open or off.
• The vehicle should not be driven for at least 24 hours or until the urethane adhesive has completely
cured. Curing time varies depending on temperature and humidity. The curing time increases under
lower temperature and lower humidity.
Inspection
INFOID:0000000006220815
REPAIRING WATER LEAKAGE FOR WINDSHIELD GLASS
Leakage can be repaired without removing the glass.
Determine the extent of leakage if water is leaking between the urethane adhesive material and body or glass.
This can be done by applying water to the windshield area while pushing glass outward.
Apply primer (if necessary) and then urethane adhesive to the leakage point to stop the leakage.
GW-14
< REMOVAL AND INSTALLATION >
SIDE WINDOW GLASS
SIDE WINDOW GLASS
Exploded View
INFOID:0000000006220816
1.
Side window glass
2.
Body side outer panel
3.
Luggage side upper finisher
4.
Adhesive
5.
Primer
6.
Back pillar garnish
7.
Rear pillar finisher
8.
Luggage side lower finisher
JMKIA5206GB
SIDE WINDOW GLASS
GW-15
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
GW
N
O
P
Removal and Installation
INFOID:0000000006220817
CAUTION:
Replace the side window glass assembly with a new part after removal as it cannot be reused.
REMOVAL
1.
Remove third seat cushion and third seatback assembly. Refer to
SE-138, "Removal and Installation"
2.
Remove luggage side lower finisher. Refer to
INT-36, "LUGGAGE SIDE LOWER FINISHER : Removal
3.
Remove rear pillar finisher. Refer to
INT-37, "REAR PILLAR FINISHER : Removal and Installation"
4.
Remove back pillar garnish. Refer to
INT-37, "BACK PILLAR GARNISH : Removal and Installation"
.
5.
Remove luggage side upper finisher. Refer to
INT-38, "LUGGAGE SIDE UPPER FINISHER : Removal
6.
Disconnect the harness connector from side window glass.
7.
Apply protective tape around the side window to protect the painted surface from damage.
8.
Remove the side window glass using piano wire.
WARNING:
Always wear safety glasses and heavy gloves to prevent injury.
CAUTION:
• Be careful not to scratch the glass when removing.
• Never set or stand the glass on its edge. Small chips may develop into cracks.
INSTALLATION
• Use a genuine Nissan Urethane Adhesive Kit (if available) or an equivalent and follow the instructions pro-
vided with it.
• Open a door window while the urethane adhesive is curing. This prevents the glass from being forced out by
passenger room air pressure when all door windows are closed.
• Inform the customer that the vehicle should remain stationary until the urethane adhesive has completely
cured (approximately 24 hours). Curing time varies with temperature and humidity.
WARNING:
• Keep heat and open flames away as primers and adhesive are flammable.
• The materials contained in the kit are harmful if swallowed, and may irritate skin and eyes. Never let
them come in contact with the skin and eyes.
• Use in an open, well ventilated location. Never breathe the vapors. They may be harmful if inhaled.
Move immediately to an area with fresh air if affected by vapor inhalation.
• Driving the vehicle before the urethane adhesive has completely cured may affect the performance
of the side window in case of an accident.
CAUTION:
• Never use an adhesive which is past its usable term. Shelf life of this product is limited to six months
after the date of manufacture. Carefully adhere to the expiration or manufacture date printed on the
box.
• Keep primers and adhesive in a cool, dry place. Ideally, they should be stored in a refrigerator.
• Never leave primers or adhesive cartridge unattended with their caps open or off.
• The vehicle should not be driven for at least 24 hours or until the urethane adhesive has completely
cured. Curing time varies depending on temperature and humidity. The curing time increases under
lower temperature and lower humidity.
Inspection
INFOID:0000000006220818
REPAIRING WATER LEAKAGE FOR SIDE WINDOW GLASS
Leakage can be repaired without removing glass.
Determine the extent of leakage if water is leaking between the urethane adhesive material and body or glass.
This can be done by applying water to the side window glass area while pushing glass outward.
Apply primer (if necessary) and then urethane adhesive to the leakage point to stop the leakage.
: Clip
: Do not reuse
Unit
: mm (in)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст