Infiniti QX56 (Z62). Manual — part 960
PB-6
< REMOVAL AND INSTALLATION >
PARKING BRAKE CONTROL
Adjustment
INFOID:0000000006222514
ADJUSTMENT AFTER INSTALLATION
Adjust the parking brake pedal stroke. Refer to
PARKING BRAKE SHOE
PB-7
< REMOVAL AND INSTALLATION >
C
D
E
G
H
I
J
K
L
M
A
B
PB
N
O
P
PARKING BRAKE SHOE
Exploded View
INFOID:0000000006222515
Removal and Installation
INFOID:0000000006222516
REMOVAL
WARNING:
Clean any dust from the parking brake shoes and back plates with a vacuum dust collector. Never
blow with compressed air.
1.
Remove rear tires with power tool.
2.
Remove disc rotor. Refer to
RAX-7, "Removal and Installation"
.
3.
Remove anti-rattle pins, retainers, anti-rattle springs, return spring and adjuster spring.
CAUTION:
Never drop the removed parts.
4.
Remove parking brake shoes, adjuster assembly, and toggle lever.
CAUTION:
Never drop the removed parts.
5.
For the removal of back plate, refer to
RAX-7, "Removal and Installation"
6.
Perform inspection after removal. Refer to
PB-8, "Inspection and Adjustment"
.
INSTALLATION
Note the following, install in the reverse order of removal.
• Apply PBC (Poly Butyl Cuprysil) grease or silicone-based grease to the back plate and brake shoe. Refer to
.
1.
Back plate
2.
Parking brake shoe
3.
Toggle lever
4.
Return spring
5.
Anti-rattle spring
6.
Retainer
7.
Anti-rattle pin
8.
Adjuster spring
9.
Adjuster
: Apply PBC (Poly Butyl Cuprysil) grease or silicone-based grease.
JPFIB0116ZZ
PB-8
< REMOVAL AND INSTALLATION >
PARKING BRAKE SHOE
• Assemble adjusters so that threaded part is expanded when rotat-
ing it in the direction shown by arrow (
).
• Shorten adjuster by rotating it.
• When disassembling apply PBC (Poly Butyl Cuprysil) grease or sil-
icone-based grease to threads.
• Check the component parts of parking brake shoe assembly are
installed properly.
• Check brake shoe sliding surface and drum inner surface for
grease. Wipe it off if it adhere on the surfaces.
• Perform adjustment after installation. Refer to
Inspection and Adjustment
INFOID:0000000006222517
INSPECTION AFTER REMOVAL
Lining Thickness Inspection
Check thickness (A) of lining.
Drum Inner Diameter Inspection
Check inner diameter (B) of drum.
Other Inspections
Check the following items, and replace the parts if necessary.
• Parking brake shoe for excessive wear, damage, and peeling.
• Anti-rattle pin and retainer for excessive wear, damage and rust.
• Adjuster spring, return spring and anti-rattle spring for settling, excessive wear, damage, and rust.
• Adjuster for smoothness.
A: For right side brake
B: For left side brake
: Vehicle front
: Adjuster expands
JPFIB0124ZZ
JPFIB0117ZZ
A
: Refer to
.
SBR021A
B
: Refer to
.
JPFIB0008ZZ
PARKING BRAKE SHOE
PB-9
< REMOVAL AND INSTALLATION >
C
D
E
G
H
I
J
K
L
M
A
B
PB
N
O
P
• Toggle lever for excessive wear, damage and rust.
• Visually check inside of the drum for excessive wear, cracks, and damage with a pair of vernier calipers.
ADJUSTMENT AFTER INSTALLATION
1.
Adjust the parking brake pedal stroke. Refer to
PB-3, "Inspection and Adjustment"
2.
Rotate the disc rotor to check that there is no drag. Install the plug. If any drag is found, follow the proce-
dure described below.
a.
Adjust parking brake stroke again.
b.
Check rear disc brake. Refer to
BR-45, "BRAKE CALIPER ASSEMBLY : Inspection"
.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст