Infiniti QX56 (Z62). Manual — part 594
EC-354
< DTC/CIRCUIT DIAGNOSIS >
[VK56VD]
P0461 FUEL LEVEL SENSOR
YES
>> INSPECTION END
NO
>> Proceed to
.
Diagnosis Procedure
INFOID:0000000006288332
1.
CHECK DTC WITH “COMBINATION METER”
MWI-30, "CONSULT-III Function"
.
Is any DTC detected?
YES
>> Perform trouble diagnosis of detected DTC.
NO
>> GO TO 2.
2.
CHECK FUEL LEVEL SENSOR SIGNAL CIRCUIT
Check fuel level sensor signal circuit. Refer to
MWI-69, "Component Function Check"
Is the inspection result normal?
YES
>> Check intermittent incident. Refer to
GI-40, "Intermittent Incident"
.
NO
>> Perform trouble diagnosis of fuel level sensor signal circuit. Refer to
P0462, P0463 FUEL LEVEL SENSOR
EC-355
< DTC/CIRCUIT DIAGNOSIS >
[VK56VD]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
P0462, P0463 FUEL LEVEL SENSOR
DTC Logic
INFOID:0000000006288333
DTC DETECTION LOGIC
NOTE:
• If DTC P0462 or P0463 is displayed with DTC UXXXX, first perform the trouble diagnosis for DTC
UXXXX.
• If DTC P0462 or P0463 is displayed with DTC P0607, first perform the trouble diagnosis for DTC
This diagnosis indicates the former, to detect open or short circuit malfunction.
DTC CONFIRMATION PROCEDURE
1.
PRECONDITIONING
1.
Turn ignition switch OFF and wait at least 10 seconds.
2.
Turn ignition switch ON.
3.
Turn ignition switch OFF and wait at least 10 seconds.
TESTING CONDITION:
Before performing the following procedure, confirm that battery voltage is 11 V or more at ignition
switch ON.
>> GO TO 2.
2.
PERFORM DTC CONFIRMATION PROCEDURE
1.
Turn ignition switch ON and wait at least 5 seconds.
2.
Check 1st trip DTC.
Is 1st trip DTC detected?
YES
>> Proceed to
.
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000006288334
1.
CHECK DTC WITH “COMBINATION METER”
MWI-30, "CONSULT-III Function"
.
Is any DTC detected?
YES
>> Perform trouble diagnosis of detected DTC.
NO
>> GO TO 2.
2.
CHECK FUEL LEVEL SENSOR SIGNAL CIRCUIT
Check fuel level sensor signal circuit. Refer to
MWI-69, "Component Function Check"
Is the inspection result normal?
YES
>> Check intermittent incident. Refer to
GI-40, "Intermittent Incident"
.
NO
>> Perform trouble diagnosis of fuel level sensor signal circuit. Refer to
DTC No.
Trouble diagnosis name
(Trouble diagnosis content)
DTC detecting condition
Possible cause
P0462
FUEL LEVL SEN/CIRC
(Fuel level sensor circuit low
input)
An excessively low voltage from the
sensor is sent to ECM.
• Harness or connectors
(The CAN communication line is open or shorted)
• Harness or connectors
(The sensor circuit is open or shorted)
• Combination meter
• Fuel level sensor
P0463
FUEL LEVL SEN/CIRC
(Fuel level sensor circuit high
input)
An excessively high voltage from
the sensor is sent to ECM.
EC-356
< DTC/CIRCUIT DIAGNOSIS >
[VK56VD]
P0500 VSS
P0500 VSS
Description
INFOID:0000000006217857
The vehicle speed signal is sent to the “combination meter” from the “ABS actuator and electric unit (control
unit)” by CAN communication line. The “combination meter” then sends a signal to the ECM by CAN commu-
nication line.
DTC Logic
INFOID:0000000006217858
DTC DETECTION LOGIC
NOTE:
• If DTC P0500 is displayed with DTC UXXXX, first perform the trouble diagnosis for DTC UXXXX.
• If DTC P0500 is displayed with DTC P0607, first perform the trouble diagnosis for DTC P0607. Refer
DTC CONFIRMATION PROCEDURE
1.
INSPECTION START
1.
Turn ignition switch OFF and wait at least 10 seconds.
2.
Turn ignition switch ON.
3.
Turn ignition switch OFF and wait at least 10 seconds.
Will CONSULT-III be used?
YES
>> GO TO 2.
NO
>> GO TO 4.
2.
CHECK VEHICLE SPEED SIGNAL
NOTE:
This procedure may be conducted with the drive wheels lifted in the shop or by driving the vehicle. If a
road test is expected to be easier, it is unnecessary to lift the vehicle.
WITH CONSULT-III
1.
Start engine (VDC switch OFF).
2.
Read “VHCL SPEED SE” in “DATA MONITOR” mode with CONSULT-III.
The vehicle speed on CONSULT-III should exceed 10 km/h (6 MPH) when rotating wheels with suitable
gear position.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Go to
3.
PERFORM DTC CONFIRMATION PROCEDURE
1.
Select “DATA MONITOR” mode with CONSULT-III.
2.
Warm engine up to normal operating temperature.
3.
Maintain the following conditions for at least 50 consecutive seconds.
CAUTION:
Always drive vehicle at a safe speed.
DTC No.
Trouble diagnosis name
(Trouble diagnosis content)
DTC detecting condition
Possible cause
P0500
VEH SPEED SEN/CIRC
(Vehicle speed sensor)
The vehicle speed signal sent to
ECM is almost 0 km/h (0 MPH) even
when vehicle is being driven.
• Harness or connectors
(The CAN communication line is open or shorted)
• Harness or connectors
(The vehicle speed signal circuit is open or shorted)
• Wheel sensor
• Combination meter
• ABS actuator and electric unit (control unit)
ENG SPEED
More than 1,500 rpm
COOLAN TEMP/S
More than 70
°
C (158
°
F)
P0500 VSS
EC-357
< DTC/CIRCUIT DIAGNOSIS >
[VK56VD]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
4.
Check 1st trip DTC.
Is 1st trip DTC detected?
YES
>> Go to
NO
>> INSPECTION END
4.
PERFORM COMPONENT FUNCTION CHECK
WITH GST
Perform Component Function Check. Refer to
EC-357, "Component Function Check"
Use Component Function Check to check the overall function of the vehicle speed signal circuit. During this
check, a 1st trip DTC might not be confirmed.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Go to
Component Function Check
INFOID:0000000006217859
1.
PERFORM COMPONENT FUNCTION CHECK
WITH GST
1.
Lift up drive wheels.
2.
Start engine.
3.
Read vehicle speed signal in Service $01 with GST.
The vehicle speed signal on GST should be able to exceed 10 km/h (6 MPH) when rotating wheels with
suitable gear position.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Go to
Diagnosis Procedure
INFOID:0000000006217860
1.
CHECK DTC WITH “ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT)”
BRC-40, "CONSULT-III Function"
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace malfunctioning part.
2.
CHECK DTC WITH “COMBINATION METER”
MWI-30, "CONSULT-III Function"
.
>> INSPECTION END
B/FUEL SCHDL
5.5 - 31.8 msec
Selector lever
Except P or N position
PW/ST SIGNAL
OFF
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст