Infiniti QX56 (Z62). Manual — part 170
REPAIRING MATERIAL
BRM-7
< PREPARATION >
C
D
E
F
G
H
I
J
L
M
A
B
BRM
N
O
P
PREPARATION
REPAIRING MATERIAL
Foam Repair
INFOID:0000000006248486
During factory body assembly, foam insulators are installed in certain body panels and locations around the
vehicle. Use the following procedure(s) to replace any factory-installed foam insulators.
URETHANE FOAM APPLICATIONS
Use commercially available Urethane foam for sealant (foam material) repair of material used on vehicle.
Read instructions on product for fill procedures.
Example of foaming agent filling operation procedure
1.
Fill procedures after installation of service part.
a.
Eliminate foam material remaining on vehicle side.
b.
Clean area after eliminating form insulator and foam material.
c.
Install service part.
d.
Insert nozzle into hole near fill area and fill foam material or fill enough to close gap with the service part.
2.
Fill procedures before installation of service part.
a.
Eliminate foam material remaining on vehicle side.
b.
Clean area after eliminating foam insulator and foam material.
c.
Fill foam material on wheelhouse outer side.
<Urethane foam for foaming agent>
3M™ Automix™ Flexible Foam 08463 or equiva-
lent
1.
Urethane foam
A.
Nozzle insert hole
: Vehicle front
JSKIA0129GB
BRM-8
< PREPARATION >
REPAIRING MATERIAL
NOTE:
Fill enough to close gap with service part while avoiding flange
area.
d.
Install service part.
NOTE:
Refer to label for information on working times.
1.
Urethane foam
A.
Fill while avoiding flange area
: Vehicle front
JSKIA0130GB
BODY COMPONENT PARTS
BRM-9
< PREPARATION >
C
D
E
F
G
H
I
J
L
M
A
B
BRM
N
O
P
BODY COMPONENT PARTS
Underbody Component Parts
INFOID:0000000006248487
: Both sided anti-corrosive precoated steel sections
: High strength steel (HSS) sections
: Both sided anti-corrosive steel and HSS sections
JSKIA1950ZZ
BRM-10
< PREPARATION >
BODY COMPONENT PARTS
NOTE:
• For the parts without a number described in the figure, it is supplied only with the assembly part that the part is included with.
• Tensile strength column shows the largest strength value of a part in the component part.
CAUTION:
If the high strength steel (ultra high strength steel) of this is broken, replace by assembly for the supply part.
No.
Parts name
Tensile strength
(MPa)
Both sided anti-corrosive
precoated steel sections
1.
Air box assembly
Under 440
×
2.
Side dash (RH & LH)
Under 440
×
3.
Lower dash
a.
T=2.0 mm
(0.079 in)
980
caution
×
4.
Trim mounting bracket assembly
Under 440
—
5.
Rear floor board reinforcement assembly
Under 440
—
6.
Jack mounting bracket
Under 440
—
7.
Rear floor rear
Under 440
×
8.
3rd seat front mounting bracket assembly
Under 440
—
9.
Rear floor reinforcement
440
—
10.
Inner rear wheelhouse reinforcement (RH & LH)
Under 440
×
11.
Rear floor front
Under 440
×
12.
2nd seat crossmember front reinforcement
Under 440
×
13.
2nd seat mounting member assembly
440
—
14.
2nd crossmember (RH & LH Upper)
Under 440
—
15.
Front seat mounting rear crossmember assembly
440
×
16.
Inner sill (RH & LH)
T=1.4 mm
(0.055 in)
980
caution
×
17.
Front floor reinforcement
440
—
18.
Front floor
Under 440
×
19.
2nd crossmember (RH & LH Lower)
440
×
20.
Hoodledge reinforcement (RH & LH)
Under 440
×
21.
Hoodledge assembly (RH & LH)
Refer to No.22
−
24
22.
Upper hoodledge (RH & LH)
Under 440
×
23.
Lower hoodledge (RH & LH)
Under 440
×
24.
Upper rear hoodledge (RH & LH)
Under 440
×
25.
Side radiator core support (RH & LH)
440
×
26.
Upper radiator core support (RH & LH)
Under 440
×
27.
Radiator core support main assembly
440
×
28.
Front side member assembly (RH & LH)
590
×
29.
4th crossmember
590
×
30.
2nd seat mounting crossmember
b.
T=2.0 mm
(0.079 in)
980
caution
×
31.
Rear side member (RH & LH)
590
×
32.
3rd seat mounting bracket assembly
Under 440
×
33.
3rd rear crossmember assembly
590
×
34.
Rear crossmember
590
×
35.
Upper rear end crossmember assembly
Under 440
×
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст