Infiniti QX56 (Z62). Manual — part 871
LAN
MAIN LINE BETWEEN DLC AND E-SUS CIRCUIT
LAN-61
< DTC/CIRCUIT DIAGNOSIS >
[CAN]
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
MAIN LINE BETWEEN DLC AND E-SUS CIRCUIT
Diagnosis Procedure
INFOID:0000000006238655
1.
CHECK CONNECTOR
1.
Turn the ignition switch OFF.
2.
Disconnect the battery cable from the negative terminal.
3.
Check the following terminals and connectors for damage, bend and loose connection (connector side
and harness side).
-
Harness connector M19
-
Harness connector B2
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair the terminal and connector.
2.
CHECK HARNESS CONTINUITY (OPEN CIRCUIT)
1.
Disconnect the harness connectors M19 and B2.
2.
Check the continuity between the data link connector and the harness connector.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair the main line between the data link connector and the harness connector M19.
3.
CHECK HARNESS CONTINUITY (OPEN CIRCUIT)
1.
Disconnect the connector of air levelizer control module.
2.
Check the continuity between the harness connector and the air levelizer control module harness connec-
tor.
Is the inspection result normal?
YES (Present error)>>Check CAN system type decision again.
YES (Past error)>>Error was detected in the main line between the data link connector and the air levelizer
control module.
NO
>> Repair the main line between the harness connector B2 and the air levelizer control module.
Data link connector
Harness connector
Continuity
Connector No.
Terminal No.
Connector No.
Terminal No.
M4
6
M19
29
Existed
14
30
Existed
Harness connector
Air levelizer control module harness connector
Continuity
Connector No.
Terminal No.
Connector No.
Terminal No.
B2
29
B84
16
Existed
30
7
Existed
LAN-62
< DTC/CIRCUIT DIAGNOSIS >
[CAN]
MAIN LINE BETWEEN E-SUS AND ADP CIRCUIT
MAIN LINE BETWEEN E-SUS AND ADP CIRCUIT
Diagnosis Procedure
INFOID:0000000006238656
1.
CHECK HARNESS CONTINUITY (OPEN CIRCUIT)
1.
Turn the ignition switch OFF.
2.
Disconnect the battery cable from the negative terminal.
3.
Disconnect the following harness connectors.
-
ECM
-
Air levelizer control module
-
Harness connectors B24 and B460
4.
Check the continuity between the air levelizer control module harness connector and the harness connec-
tor.
Is the inspection result normal?
YES (Present error)>>Check CAN system type decision again.
YES (Past error)>>Error was detected in the main line between the air levelizer control module and the driver
seat control unit.
NO
>> Repair the main line between the air levelizer control module and the harness connector B24.
Air levelizer control module harness connector
Harness connector
Continuity
Connector No.
Terminal No.
Connector No.
Terminal No.
B84
16
B24
13
Existed
7
12
Existed
LAN
MAIN LINE BETWEEN ADP AND PWBD CIRCUIT
LAN-63
< DTC/CIRCUIT DIAGNOSIS >
[CAN]
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
MAIN LINE BETWEEN ADP AND PWBD CIRCUIT
Diagnosis Procedure
INFOID:0000000006220540
1.
CHECK HARNESS CONTINUITY (OPEN CIRCUIT)
1.
Turn the ignition switch OFF.
2.
Disconnect the battery cable from the negative terminal.
3.
Disconnect the following harness connectors.
-
CAN gateway
-
Harness connectors B460 and B24
-
Automatic back door control module
4.
Check the continuity between the harness connector and the automatic back door control module harness
connector.
Is the inspection result normal?
YES (Present error)>>Check CAN system type decision again.
YES (Past error)>>Error was detected in the main line between the driver seat control unit and the automatic
back door control module.
NO
>> Repair the main line between the harness connector B24 and the automatic back door control
module.
Harness connector
Automatic back door control module
harness connector
Continuity
Connector No.
Terminal No.
Connector No.
Terminal No.
B24
13
B26
7
Existed
12
6
Existed
LAN-64
< DTC/CIRCUIT DIAGNOSIS >
[CAN]
MAIN LINE BETWEEN RDR-R AND RDR-L CIRCUIT
MAIN LINE BETWEEN RDR-R AND RDR-L CIRCUIT
Diagnosis Procedure
INFOID:0000000006220541
1.
CHECK CONNECTOR
1.
Turn the ignition switch OFF.
2.
Disconnect the battery cable from the negative terminal.
3.
Check the following terminals and connectors for damage, bend and loose connection (connector side
and harness side).
-
Harness connector B239
-
Harness connector B63
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair the terminal and connector.
2.
CHECK HARNESS CONTINUITY (OPEN CIRCUIT)
1.
Disconnect the following harness connectors.
-
Side radar RH
-
Harness connectors B239 and B63
2.
Check the continuity between the side radar RH harness connector and the harness connector.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair the main line between the side radar RH and the harness connector B239.
3.
CHECK HARNESS CONTINUITY (OPEN CIRCUIT)
1.
Disconnect the connector of side radar LH.
2.
Check the continuity between the harness connector and the side radar LH harness connector.
Is the inspection result normal?
YES (Present error)>>Check CAN system type decision again.
YES (Past error)>>Error was detected in the main line between the side radar RH and the side radar LH.
NO
>> Repair the main line between the harness connector B63 and the side radar LH.
Side radar RH harness connector
Harness connector
Continuity
Connector No.
Terminal No.
Connector No.
Terminal No.
B243
4
B239
7
Existed
3
3
Existed
Harness connector
Side radar LH harness connector
Continuity
Connector No.
Terminal No.
Connector No.
Terminal No.
B63
7
B74
4
Existed
3
3
Existed
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст