Infiniti QX56 (Z62). Manual — part 212
CCS
C1A26 ECD MODE MALFUNCTION
CCS-115
< DTC/CIRCUIT DIAGNOSIS >
[ICC]
C
D
E
F
G
H
I
J
K
L
M
B
N
P
A
C1A26 ECD MODE MALFUNCTION
DTC Logic
INFOID:0000000006224347
DTC DETECTION LOGIC
NOTE:
If DTC “C1A26” is detected along with DTC “U1000”, “U0415” or “U0121” first diagnose the DTC “U1000”,
“U0415” or “U0121”.
• DTC “U1000”: Refer to
CCS-145, "ADAS CONTROL UNIT : DTC Logic"
CCS-141, "ADAS CONTROL UNIT : DTC Logic"
CCS-133, "ADAS CONTROL UNIT : DTC Logic"
DTC CONFIRMATION PROCEDURE
1.
PERFORM DTC CONFIRMATION PROCEDURE
1.
Start the engine.
2.
Wait for approximately 1 minute after turning the MAIN switch of ICC system ON.
3.
Perform “All DTC Reading” with CONSULT-III.
4.
Check if the “C1A26” is detected as the current malfunction in “Self Diagnostic Result” of “ICC/ADAS”.
Is “C1A26” detected as the current malfunction?
YES
>> Refer to
CCS-115, "Diagnosis Procedure"
.
NO
>> Refer to
GI-40, "Intermittent Incident"
.
Diagnosis Procedure
INFOID:0000000006224348
1.
CHECK SELF-DIAGNOSIS RESULTS
Check if “U1000”, “U0415” or “U0121” is detected other than “C1A26” in “Self Diagnostic Result” of “ICC/
ADAS”.
Is any DTC detected?
YES
>> Perform diagnosis on the detected DTC and repair or replace the malfunctioning parts. Refer to
NO
>> GO TO 2.
2.
PERFORM SELF-DIAGNOSIS OF ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT)
Check if any DTC is detected in “Self Diagnostic Result” of “ABS”.
Is any DTC detected?
YES
>> Perform diagnosis on the detected DTC and repair or replace the malfunctioning parts. Refer to
NO
>> Replace ADAS control unit. Refer to
DAS-63, "Removal and Installation"
DTC
(On board
display)
Trouble diagnosis name
DTC detecting condition
Possible cause
C1A26
(26)
ECD MODE MALF
If an abnormal condition occurs with ECD system
ABS actuator and electric unit (control
unit)
CCS-116
< DTC/CIRCUIT DIAGNOSIS >
[ICC]
C1A27 ECD POWER SUPPLY CIRCUIT
C1A27 ECD POWER SUPPLY CIRCUIT
DTC Logic
INFOID:0000000006224349
DTC DETECTION LOGIC
NOTE:
If DTC “C1A27” is detected along with DTC “U1000”, “U0415” or “U0121” first diagnose the DTC “U1000”,
“U0415” or “U0121”.
• DTC “U1000”: Refer to
CCS-145, "ADAS CONTROL UNIT : DTC Logic"
• DTC “U0415”: Refer to
CCS-141, "ADAS CONTROL UNIT : DTC Logic"
• DTC “U0121”: Refer to
CCS-133, "ADAS CONTROL UNIT : DTC Logic"
DTC CONFIRMATION PROCEDURE
1.
PERFORM DTC CONFIRMATION PROCEDURE
1.
Start the engine.
2.
Wait for approximately 1 minute after turning the MAIN switch of ICC system ON.
3.
Perform “All DTC Reading” with CONSULT-III.
4.
Check if the “C1A27” is detected as the current malfunction in “Self Diagnostic Result” of “ICC/ADAS”.
Is “C1A27” detected as the current malfunction?
YES
>> Refer to
CCS-116, "Diagnosis Procedure"
NO
>> Refer to
GI-40, "Intermittent Incident"
.
Diagnosis Procedure
INFOID:0000000006224350
1.
CHECK SELF-DIAGNOSIS RESULTS
Check if “U1000”, “U0415” or “U0121” is detected other than “C1A27” in “Self Diagnostic Result” of “ICC/
ADAS”.
Is any DTC detected?
YES
>> Perform diagnosis on the detected DTC and repair or replace the malfunctioning parts. Refer to
.
NO
>> GO TO 2.
2.
CHECK POWER SUPPLY CIRCUIT OF ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT)
Check power supply circuit of ABS actuator and electric unit (control unit). Refer to
Is the inspection result normal?
YES
>> Perform self-diagnosis of ABS actuator and electric unit (control unit). Refer to
.
NO
>> Repair the harnesses or connectors.
DTC
(On board
display)
Trouble diagnosis name
DTC detecting condition
Possible cause
C1A27
(27)
ECD PWR SUPLY CIR
ECD system power supply voltage is excessively
low
• ABS actuator and electric unit (con-
trol unit) power supply circuit
• ABS actuator and electric unit (con-
trol unit)
CCS
C1A2A ICC SENSOR POWER SUPPLY CIRCUIT
CCS-117
< DTC/CIRCUIT DIAGNOSIS >
[ICC]
C
D
E
F
G
H
I
J
K
L
M
B
N
P
A
C1A2A ICC SENSOR POWER SUPPLY CIRCUIT
DTC Logic
INFOID:0000000006224351
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
PERFORM DTC CONFIRMATION PROCEDURE
1.
Start the engine.
2.
Turn the MAIN switch of ICC system ON.
3.
Perform “All DTC Reading” with CONSULT-III.
4.
Check if the “C1A2A” is detected as the current malfunction in “Self Diagnostic Result” of “ICC/ADAS”.
Is “C1A2A” detected as the current malfunction?
YES
>> Refer to
CCS-117, "Diagnosis Procedure"
.
NO
>> Refer to
GI-40, "Intermittent Incident"
.
Diagnosis Procedure
INFOID:0000000006224352
1.
CHECK SELF-DIAGNOSIS RESULTS
Check if “U1000” is detected other than “C1A2A” in “Self Diagnostic Result” of “ICC/ADAS”.
Is any DTC detected?
YES
>> Perform diagnosis on the detected DTC and repair or replace the malfunctioning parts. Refer to
CCS-145, "ADAS CONTROL UNIT : DTC Logic"
NO
>> GO TO 2.
2.
CHECK ICC SENSOR SELF-DIAGNOSIS
Check if any DTC is detected in “Self Diagnostic Result” of “LASER”.
Is any DTC detected?
YES
>> Perform diagnosis on the detected DTC and repair or replace the malfunctioning parts. Refer to
NO
>> Replace ADAS control unit. Refer to
DAS-63, "Removal and Installation"
DTC
(On board
display)
Trouble diagnosis name
DTC detecting condition
Possible cause
C1A2A
(80)
ICC SEN PWR SUP CIR
Abnormal power supply voltage in ICC sensor
• Harness, connector, fuse
• ICC sensor
CCS-118
< DTC/CIRCUIT DIAGNOSIS >
[ICC]
C1A33 CAN TRANSMISSION ERROR
C1A33 CAN TRANSMISSION ERROR
DTC Logic
INFOID:0000000006224353
DTC DETECTION LOGIC
NOTE:
If DTC “C1A33” is detected along with DTC “U1000”, first diagnose the DTC “U1000”. Refer to
"ADAS CONTROL UNIT : DTC Logic"
DTC CONFIRMATION PROCEDURE
1.
PERFORM DTC CONFIRMATION PROCEDURE
1.
Start the engine.
2.
Turn the MAIN switch of ICC system ON.
3.
Perform “All DTC Reading” with CONSULT-III.
4.
Check if the “C1A33” is detected as the current malfunction in “Self Diagnostic Result” of “ICC/ADAS”.
Is “C1A33” detected as the current malfunction?
YES
>> Refer to
CCS-118, "Diagnosis Procedure"
NO
>> Refer to
GI-40, "Intermittent Incident"
.
Diagnosis Procedure
INFOID:0000000006224354
1.
CHECK SELF-DIAGNOSIS RESULTS
Check if “U1000” is detected other than “C1A33” in “Self Diagnostic Result” of “ICC/ADAS”.
Is “U1000” detected?
YES
>> Perform the CAN communication system inspection. Repair or replace the malfunctioning parts.
CCS-145, "ADAS CONTROL UNIT : DTC Logic"
.
NO
>> Replace the ADAS control unit. Refer to
DAS-63, "Removal and Installation"
DTC
(On board dis-
play)
Trouble diagnosis name
DTC detecting condition
Possible causes
C1A33
(33)
CAN TRANSMISSION
ERR
If an error occurs in the CAN communication
signal that ADAS control unit transmits to ECM
ADAS control unit
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст