Infiniti QX56 (Z62). Manual — part 1150
SE-138
< REMOVAL AND INSTALLATION >
THIRD SEAT
Removal and Installation
INFOID:0000000006217436
REMOVAL
CAUTION:
When removing and installing, use shop cloths to protect parts from damage.
1.
Remove the headrest.
2.
Remove the leg cover.
1.
Pull up the front edge of the leg cover to release the pawls.
2.
Slide the leg cover forward to release the pawls.
3.
Remove the mounting bolts on the front side of the third seat.
4.
Operate fold down switch or reclining switch, and fold down seatback LH and RH.
5.
Remove the luggage floor bracket.
1.
Remove the luggage floor rear board. Refer to
INT-34, "LUGGAGE FLOOR REAR BOARD :
.
2.
Remove the mounting nuts and screws of the luggage floor bracket.
6.
Disconnect harness connector (A) and remove harness clip (B) of seat harness assembly.
7.
Remove the seat belt anchor plate.
8.
Remove the mounting nuts on the rear side of the third seat.
9.
Remove the third seat assembly from vehicle.
CAUTION:
When removing and installing, use shop cloths to protect parts from damage.
INSTALLATION
10. Seat cushion pad
11.
Leg cover RH
12. Seat hinge assembly RH
13. Seat hinge assembly LH
14. Leg cover LH
15. Seat harness LH
16. Seat bracket assembly LH
17. Seatback silencer LH
18. Headrest LH
19. Seatback board LH
20. Seatback board RH
21. Seatback board clip
22. Luggage floor bracket
23. Seat belt anchor nut
24. Seat belt anchor bolt
25. Seat belt buckle RH
26. Seat belt buckle (center)
27. Seat belt anchor plate
28. Seat belt connector buckle
29. Seat belt buckle LH
30. Hinge cover RH
31. Seatback inner arm cover RH
32. Seatback inner arm cover LH
33. Hinge cover LH
34. Seatback support
35. Seatback frame RH
36. Bush
37. Seat cushion frame RH
38. Seat cushion frame LH
39. Seatback frame LH
: Pawl
Refer to
for symbols in the figure.
: Pawl
JMJIA3899ZZ
JMJIA4264ZZ
THIRD SEAT
SE-139
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
SE
N
O
P
Install in the reverse order of removal.
Disassembly and Assembly
INFOID:0000000006217437
SEATBACK
Disassembly
1.
Remove the hinge cover.
1.
Remove the seat cushion trim and seat cushion pad from seat cushion frame.
2.
Remove the fixing screws, and then remove the hinge cover.
2.
Remove the mounting bolts, and then remove the seatback assembly.
3.
Open fastener (A) of seatback trim.
• LH side
• RH side
4.
Remove clips that retain seatback board and seatback trim.
5.
Remove the seatback board and the clips.
1.
Slide and align the clips (B) to the holes on the seatback
board (A) as shown in the figure, and then remove the seat-
back board (A).
2.
Remove the clips after removing the seatback board.
6.
Remove the seatback trim and seatback pad.
JMJIA4328ZZ
JMJIA4329ZZ
JMJIA4076ZZ
SE-140
< REMOVAL AND INSTALLATION >
THIRD SEAT
1.
Remove the headrest holder.
CAUTION:
Before installing headrest holder check its orientation.
(front/rear and right/left)
2.
Remove the seatback trim and pad from seatback frame.
3.
Remove the hog rings to separate the seatback trim and seatback pad.
7.
Remove the seatback silencer.
8.
Remove the seatback inner arm cover (RH and LH).
Assembly
Assemble in the reverse order of disassembly.
CAUTION:
• Install the hog rings of seatback trim in position, and then securely connect the trim or trim cord with
the seatback frame.
• When installing wire, be careful that it is not slackened.
SEAT CUSHION
Disassembly
1.
Remove the seat cushion trim and seat cushion pad.
1.
Remove the seat cushion retainer.
2.
Remove the seat cushion trim and seat cushion pat from seat cushion frame.
3.
Remove the hog rings to separate the seatback trim and seatback pad.
2.
Remove the hinge cover.
Remove the fixing screws, and then remove the hinge cover.
3.
Remove the mounting bolts, and then remove the seat cushion assembly.
4.
Remove the mounting nuts, and then remove the seat hinge assembly.
Assembly
Assemble in the reverse order of disassembly.
CAUTION:
Install the hog rings of seat cushion trim in position, and then securely connect the trim or trim cord
with the seat cushion pad wire.
PIIB4084J
POWER SEAT SWITCH
SE-141
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
SE
N
O
P
POWER SEAT SWITCH
Removal and Installation
INFOID:0000000006217438
REMOVAL
CAUTION:
When removing and installing, use shop cloths to protect parts from damage.
1.
Remove the seat. Refer to
SE-112, "Removal and Installation"
.
2.
Remove the seat cushion outer finisher.
3.
Disconnect power seat switch connector.
4.
Remove the screws.
5.
Remove the power seat switch from the seat.
INSTALLATION
Install in the reverse order of removal.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст