Infiniti QX56 (Z62). Manual — part 935
MIR-32
< REMOVAL AND INSTALLATION >
OUTSIDE MIRROR
OUTSIDE MIRROR
Exploded View
INFOID:0000000006257236
DOOR MIRROR ASSEMBLY
DOOR MIRROR ASSEMBLY : Removal and Installation
INFOID:0000000006257237
REMOVAL
1.
Remove front door finisher and door mirror corner cover. Refer to
INT-14, "Removal and Installation"
.
2.
Disconnect door mirror assembly harness connector.
3.
Remove door mirror mounting nuts, and then remove door mirror assembly.
1.
Door mirror cover
2.
Glass mirror
3.
Actuator assembly
4.
Connector
5.
Door mirror cover
6.
Side camera finisher
7.
Around view camera
8.
Side turn signal lamp
9.
Housing
10. Bracket
11.
Power fold unit
12. Base cover
13. Puddle lamp
14. Base
: Clip
: Pawl
JMLIA1144ZZ
OUTSIDE MIRROR
MIR-33
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
K
M
A
B
MIR
N
O
P
INSTALLATION
Note the following item, and then install in the reverse order of removal.
CAUTION:
Perform camera image calibration (with side camera models). Refer to
.
DOOR MIRROR ASSEMBLY : Disassembly and Assembly
INFOID:0000000006257238
DISASSEMBLY
1.
Remove door mirror assembly from front door panel. Refer to
MIR-32, "DOOR MIRROR ASSEMBLY :
.
2.
Remove glass mirror. Refer to
MIR-35, "GLASS MIRROR : Removal and Installation"
.
3.
Remove door mirror cover. Refer to
MIR-36, "DOOR MIRROR COVER : Removal and Installation"
4.
Remove actuator.
1.
Remove actuator (1) fixing screws (A).
2.
Disconnect the harness connectors behind the actuator.
NOTE:
Disconnect the harness connector (B) of automatic driving posi-
tion system (2) if equipped.
5.
Remove side camera finisher assembly (1).
1.
Remove side camera finisher fixing screw (A).
JMLIA0910ZZ
JMLIA0911ZZ
JMLIA0912ZZ
MIR-34
< REMOVAL AND INSTALLATION >
OUTSIDE MIRROR
2.
Disconnect harness connector (B), and remove screws (C)
and pawl (D) fixing the side camera finisher (1) to housing.
3.
Remove side turn signal lamp fixing screws (E), and then
remove side turn signal lamp.
NOTE:
Pull slightly side camera finisher (1) covering side turn sig-
nal lamp bottom screw.
4.
Remove side camera finisher assembly.
5.
Remove around view camera. Refer to
AV-233, "Removal and Installation"
6.
Remove all the harness connector terminal from the connector.
NOTE:
Write a short note to describe connector terminal layout before starting operation.
7.
Remove base.
1.
Remove base cover.
Remove base cover fixing pawls with a flat-bladed screw-
driver (A) wrapped into a tape.
CAUTION:
Apply protective tape (B) around the base to protect the
surface from damage.
2.
Remove puddle lamp. Refer to
INL-79, "Removal and Installation"
3.
Remove base mounting bolts located under base cover.
4.
Remove base.
8.
Remove the fixing screws (A), and then remove power fold unit and bracket from housing.
JMLIA0913ZZ
JMLIA0914ZZ
: Pawl
JMLIA1146ZZ
JMLIA0923ZZ
OUTSIDE MIRROR
MIR-35
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
K
M
A
B
MIR
N
O
P
9.
Remove fixing screws (A), (B) and then remove power fold unit (2) from bracket (1).
ASSEMBLY
Assemble in the reverse order of disassembly.
GLASS MIRROR
GLASS MIRROR : Removal and Installation
INFOID:0000000006257239
REMOVAL
1.
Remove door mirror assembly from front door. Refer to
MIR-32, "DOOR MIRROR ASSEMBLY : Removal
2.
Remove glass mirror.
1.
Place the glass mirror upward.
2.
Put a strip of protective tape (B) on housing assembly.
3.
As shown in the figure, insert a small flat-bladed screwdriver
(A) between glass mirror (1) and actuator (2). Push up both
pawls simultaneously to remove glass mirror lower half side.
NOTE:
Insert flat-bladed screwdriver into recesses, and push up
while rotating (twisting) to make work easier.
4.
Remove terminals (A) of mirror heater attachment from
glass mirror (1) if equipped.
3.
Lightly lift up lower side of glass mirror, and detach both pawls of upper side as if pulling it out to disas-
semble glass mirror from actuator.
NOTE:
Be careful not to allow grease on sealing agent in center of mirror or back side of glass mirror.
INSTALLATION
Note the following item, and then install in the reverse order n the reverse order of disassembly.
CAUTION:
After installation, visually check that pawls are securely engaged.
DOOR MIRROR COVER
JMLIA0924ZZ
JMLIA0158ZZ
JMLIA0908ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст