Infiniti QX56 (Z62). Manual — part 101
BCS-18
< SYSTEM DESCRIPTION >
DIAGNOSIS SYSTEM (BCM)
INT LAMP : CONSULT-III Function (BCM - INT LAMP)
INFOID:0000000006376481
WORK SUPPORT
DATA MONITOR
JMLIA0961GB
Service item
Setting item
Setting
SET I/L D-UNLCK INTCON
On*
With the interior room lamp timer function
Off
Without the interior room lamp timer function
ROOM LAMP TIMER SET
MODE 2
7.5 sec.
Sets the interior room lamp ON time. (Timer operating time)
MODE 3*
15 sec.
MODE 4
30 sec.
ROOM LAMP ON TIME SET
MODE 1
0.5 sec.
Sets the interior room lamp gradual brightening time.
MODE 2
1 sec.
MODE 3
2 sec.
MODE 4
3 sec.
MODE 5
0 sec.
MODE 6*
Gradually brightens from 0% to 100% brightness in 1 second.
ROOM LAMP OFF TIME SET
MODE 1
0.5 sec.
Sets the interior room lamp gradual dimming time.
MODE 2
1 sec.
MODE 3
2 sec.
MODE 4
3 sec.
MODE 5
0 sec.
MODE 6*
Gradually dims from 100% to 0% in 1 second.
R LAMP TIMER LOGIC SET
MODE 1*
Interior room lamp timer activates with synchronizing all doors.
MODE 2
Interior room lamp timer activates with synchronizing the driver door only.
Monitor item
[Unit]
Description
REQ SW-DR
[On/Off]
The switch status input from door request switch (driver side)
REQ SW-AS
[On/Off]
The switch status input from door request switch (passenger side)
REQ SW-RR
[On/Off]
NOTE:
The item is indicated, but not monitored.
REQ SW-RL
[On/Off]
BCS
DIAGNOSIS SYSTEM (BCM)
BCS-19
< SYSTEM DESCRIPTION >
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
ACTIVE TEST
HEADLAMP
HEADLAMP : CONSULT-III Function (BCM - HEAD LAMP)
INFOID:0000000006376461
WORK SUPPORT
PUSH SW
[On/Off]
The switch status input from push-button ignition switch
UNLK SEN -DR
[On/Off]
Driver door unlock status input from unlock sensor
DOOR SW-DR
[On/Off]
The switch status input from door switch (driver side)
DOOR SW-AS
[On/Off]
The switch status input from door switch (passenger side)
DOOR SW-RR
[On/Off]
The switch status input from rear door switch RH
DOOR SW- RL
[On/Off]
The switch status input from rear door switch LH
DOOR SW- BK
[On/Off]
The switch status input from back door switch
CDL LOCK SW
[On/Off]
Lock switch status input from door lock and unlock switch
CDL UNLOCK SW
[On/Off]
Unlock switch status input from door lock and unlock switch
KEY CYL LK-SW
[On/Off]
Lock switch status received from door key cylinder switch
KEY CYL UN-SW
[On/Off]
Unlock switch status received from door key cylinder switch
TRNK/HAT MNTR
[On/Off]
NOTE:
The item is indicated, but not monitored.
RKE-LOCK
[On/Off]
Lock signal status received from remote keyless entry receiver
RKE-UNLOCK
[On/Off]
Unlock signal status received from remote keyless entry receiver
Monitor item
[Unit]
Description
Test item
Operation
Description
INT LAMP
On
Outputs the interior room lamp control signal to turn the interior room lamps ON.
[Map lamp, personal lamp, foot lamp (when applicable lamps switch is in DOOR po-
sition.)]
Off
Stops the interior room lamp control signal to turn the interior room lamps OFF.
STEP LAMP TEST
On
Outputs the step lamp control signal to turn the step lamps ON.
Off
Stops the step lamp control signal to turn the step lamps ON.
Service item
Setting item
Setting
CUSTOM A/LIGHT SETTING
MODE 1*
1
Normal
MODE 2
More sensitive setting than normal setting (Turns ON earlier than normal opera-
tion)
MODE 3
More sensitive setting than MODE 2 (Turns ON earlier than MODE 2)
MODE 4
Less sensitive setting than normal setting (Turns ON later than normal operation)
BCS-20
< SYSTEM DESCRIPTION >
DIAGNOSIS SYSTEM (BCM)
*
1
: Factory setting
*
2
: For models for Canada, this item is displayed but is not operated.
DATA MONITOR
BATTERY SAVER SET
On*
1
With the exterior lamp battery saver function
Off
Without the exterior lamp battery saver function
ILL DELAY SET
MODE 1*
1
45 sec.
Sets delay timer function timer operation time
(All doors closed)
MODE 2
Without the
function
MODE 3
30 sec.
MODE 4
60 sec.
MODE 5
90 sec.
MODE 6
120 sec.
MODE 7
150 sec.
MODE 8
180 sec.
AUTO LIGHT LOGIC SET*
2
MODE 1*
1
With twilight ON custom & with wiper INT, LO and HI
MODE 2
With twilight ON custom & with wiper LO and HI
MODE 3
With twilight ON custom & without
MODE 4
Without twilight ON custom & with wiper INT, LO and HI
MODE 5
Without twilight ON custom & with wiper LO and HI
MODE 6
Without twilight ON custom & without
Service item
Setting item
Setting
Monitor item
[Unit]
Description
PUSH SW
[On/Off]
The switch status input from push-button ignition switch
ENGINE STATE
[Stop/Stall/Crank/Run]
The engine status received from ECM via CAN communication
VEH SPEED 1
[km/h]
The value of the vehicle speed received from combination meter via CAN communi-
cation
TURN SIGNAL R
[On/Off]
Each switch status that BCM judges from the combination switch reading function
TURN SIGNAL L
[On/Off]
TAIL LAMP SW
[On/Off]
HI BEAM SW
[On/Off]
HEAD LAMP SW1
[On/Off]
HEAD LAMP SW2
[On/Off]
PASSING SW
[On/Off]
AUTO LIGHT SW
[On/Off]
FR FOG SW
[On/Off]
RR FOG SW
[On/Off]
NOTE:
This item is indicated, but can not monitored
BCS
DIAGNOSIS SYSTEM (BCM)
BCS-21
< SYSTEM DESCRIPTION >
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
ACTIVE TEST
*: Only models for Canada display this item.
WIPER
WIPER : CONSULT-III Function (BCM - WIPER)
INFOID:0000000006376469
WORK SUPPORT
DOOR SW-DR
[On/Off]
The switch status input from front door switch (driver side)
DOOR SW-AS
[On/Off]
The switch status input from front door switch (passenger side)
DOOR SW-RR
[On/Off]
The switch status input from rear door switch RH
DOOR SW- RL
[On/Off]
The switch status input from rear door switch LH
DOOR SW-BK
[On/Off]
The switch status input from back door switch
OPTICAL SENSOR
[On/Off]
The sensor status input from optical sensor
OPTI SEN (DTCT)
[V]
The value of outside brightness voltage input from the optical sensor
OPTI SEN (FILT)
[V]
The value of outside brightness voltage filtered by BCM
Monitor item
[Unit]
Description
Test item
Operation
Description
TAIL LAMP
On
Transmits the position light request signal to IPDM E/R via CAN commu-
nication to turn the tail lamp ON
Off
Stops the tail lamp request signal transmission
HEAD LAMP
Hi
Transmits the high beam request signal via CAN communication to turn
the headlamp (HI)
Lo
Transmits the low beam request signal via CAN communication to turn
the headlamp (LO)
Off
Stops the high & low beam request signal transmission
FR FOG LAMP
On
Transmits the front fog lights request signal to IPDM E/R via CAN com-
munication to turn the front fog lamp ON
Off
Stops the front light request signal transmission
RR FOG LAMP
On
NOTE:
This item is indicated, but can not tested
Off
DAYTIME RUNNING LIGHT*
On
Transmits the front fog lights request signal to IPDM E/R via CAN com-
munication to turn the front fog lamp ON (daytime running light system)
Off
Stops the front light request signal transmission (daytime running light
system)
ILL DIM SIGNAL
On
• Transmits the dimmer signal to combination meter via CAN communi-
cation and dims combination meter
• Transmits the dimmer signal to AV control unit and dims display
Off
Stops the dimmer signal transmission
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст