Infiniti QX56 (Z62). Manual — part 1051
REAR WHEEL HUB AND HOUSING
RAX-5
< PERIODIC MAINTENANCE >
C
E
F
G
H
I
J
K
L
M
A
B
RAX
N
O
P
PERIODIC MAINTENANCE
REAR WHEEL HUB AND HOUSING
Inspection
INFOID:0000000006225463
MOUNTING INSPECTION
Check the mounting conditions (looseness, back lash) of each component and component conditions (wear,
damage) are normal.
WHEEL BEARING INSPECTION
• Move wheel hub and bearing assembly in the axial direction by hand. Check there is no looseness of wheel
hub and bearing assembly.
• Rotate wheel hub and bearing assembly, and check there is no unusual noise or other irregular conditions. If
there is any of irregular conditions, replace wheel hub and bearing assembly.
Axial end play
: Refer to
.
RAX-6
< PERIODIC MAINTENANCE >
REAR DRIVE SHAFT
REAR DRIVE SHAFT
Inspection
INFOID:0000000006225464
Check the following items, and replace the part if necessary.
• Check drive shaft mounting point and joint for looseness and other damage.
CAUTION:
Replace entire drive shaft assembly when noise or vibration occurs from drive shaft.
• Check boot for cracks and other damage.
REAR WHEEL HUB AND HOUSING
RAX-7
< REMOVAL AND INSTALLATION >
C
E
F
G
H
I
J
K
L
M
A
B
RAX
N
O
P
REMOVAL AND INSTALLATION
REAR WHEEL HUB AND HOUSING
Exploded View
INFOID:0000000006225465
Removal and Installation
INFOID:0000000006225466
REMOVAL
1.
Remove tires with power tool. Refer to
WT-64, "Removal and Installation"
.
2.
Remove brake hose bracket from suspension arm. Refer to
BR-26, "REAR : Removal and Installation"
3.
Remove caliper assembly. Hang caliper assembly in a place where it will not interfere with work. Refer to
BR-43, "BRAKE CALIPER ASSEMBLY : Removal and Installation"
CAUTION:
Never depress brake pedal while caliper assembly is removed.
4.
Remove disc rotor. If disc rotor cannot be removed, remove as follows.
CAUTION:
• Parking brake completely in the released position.
• Put matching marks on the wheel hub and bearing assembly and the disc rotor before removing
the disc rotor.
• Never drop disc rotor.
a.
Fix the disc rotor with wheel nuts and remove the adjusting hole plug.
1.
Axle housing
2.
Bushing
3.
Back plate
4.
Anchor block
5.
Hub bolt
6.
Wheel hub and bearing assembly
7.
Disc rotor
8.
Plug
9.
Wheel hub lock nut
10. Adjusting cap
11.
Cotter pin
A.
Tightening must be done following the installation procedure. Refer to
RAX-7, "Removal and Installation"
Refer to
JPDIG0199GB
RAX-8
< REMOVAL AND INSTALLATION >
REAR WHEEL HUB AND HOUSING
b.
Using suitable tool, rotate adjuster (1) in the direction (A) to
retract and loosen brake shoe.
5.
Remove wheel sensor harness. Refer to
WHEEL SENSOR : Removal and Installation"
6.
Remove parking brake shoe and parking brake cable from back
plate. Refer to
PB-7, "Removal and Installation"
7.
Remove height sensor from rear lower link (right side). Refer to
EXL-136, "Removal and Installation"
8.
Remove vehicle height sensor from rear lower link (left side).
Refer to
SCS-98, "Removal and Installation"
9.
Set suitable jack under rear lower link.
10. Remove rear lower link from axle housing. Refer to
RSU-8, "Removal and Installation"
.
11. Remove coil spring. Refer to
RSU-8, "Removal and Installation"
.
12. Remove cotter pin and adjusting cap, then loosen wheel hub lock nut.
13. Put matching mark (A) on drive shaft and wheel hub and bearing
assembly.
CAUTION:
Use paint or similar substance for matching marks. Never
scratch the surface.
14. Patch wheel hub lock nut with a piece of wood. Hammer the
wood to disengage wheel hub and bearing assembly from drive
shaft.
CAUTION:
• Never place drive shaft joint at an extreme angle. Also be
careful not to overextend slide joint.
• Never allow drive shaft to hang down without support for
counterpart such as joint sub-assembly, and other parts.
NOTE:
Use a suitable puller, if wheel hub and bearing assembly and drive shaft cannot be separated even after
performing the above procedure.
15. Remove wheel hub lock nut.
16. Remove suspension arm from axle housing.
CAUTION:
Never damage ball joint boot.
17. Remove front lower link from axle housing.
CAUTION:
Never damage ball joint boot.
18. Remove axle housing.
19. Remove wheel hub and bearing assembly.
20. Remove anchor block mounting nuts, and then remove anchor block and back plate from axle housing.
21. Remove hub bolts (1) from wheel hub and bearing assembly,
using the ball joint remover (A) (commercial service tool).
CAUTION:
• Remove hub bolt only when necessary.
• Never hammer the hub bolt to avoid impact to the wheel
hub and bearing assembly.
• Pull out the hub bolt in a direction perpendicular to the
wheel hub and bearing assembly.
22. Perform inspection after removal. Refer to
.
INSTALLATION
Note the following, and install in the reverse order of removal.
JPFIB0014ZZ
JPDIG0121ZZ
JPDIF0299ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст