Infiniti QX56 (Z62). Manual — part 280
DAS
C1A27 ECD POWER SUPPLY CIRCUIT
DAS-157
< DTC/CIRCUIT DIAGNOSIS >
[DCA]
C
D
E
F
G
H
I
J
K
L
M
B
N
P
A
C1A27 ECD POWER SUPPLY CIRCUIT
DTC Logic
INFOID:0000000006228096
DTC DETECTION LOGIC
NOTE:
If DTC “C1A27” is detected along with DTC “U1000”, “U0415” or “U0121” first diagnose the DTC “U1000”,
“U0415” or “U0121”.
• DTC “U1000”: Refer to
DAS-182, "ADAS CONTROL UNIT : DTC Logic"
DTC CONFIRMATION PROCEDURE
1.
PERFORM DTC CONFIRMATION PROCEDURE
1.
Start the engine.
2.
Wait for approximately 1 minute after turning the DCA system ON.
3.
Perform “All DTC Reading” with CONSULT-III.
4.
Check if the “C1A27” is detected as the current malfunction in “Self Diagnostic Result” of “ICC/ADAS”.
Is “C1A27” detected as the current malfunction?
YES
>> Refer to
DAS-157, "Diagnosis Procedure"
NO
>> Refer to
GI-40, "Intermittent Incident"
.
Diagnosis Procedure
INFOID:0000000006228097
1.
CHECK SELF-DIAGNOSIS RESULTS
Check if “U1000”, “U0415” or “U0121” is detected other than “C1A27” in “Self Diagnostic Result” of “ICC/
ADAS”.
Is any DTC detected?
YES
>> Perform diagnosis on the detected DTC and repair or replace the malfunctioning parts. Refer to
NO
>> GO TO 2.
2.
CHECK POWER SUPPLY CIRCUIT OF ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT)
Check power supply circuit of ABS actuator and electric unit (control unit). Refer to
Is the inspection result normal?
YES
>> Perform self-diagnosis of ABS actuator and electric unit (control unit). Refer to
.
NO
>> Repair the harnesses or connectors.
DTC
(On board
display)
Trouble diagnosis name
DTC detecting condition
Possible cause
C1A27
(27)
ECD PWR SUPLY CIR
ECD system power supply voltage is excessively
low
• ABS actuator and electric unit (con-
trol unit) power supply circuit
• ABS actuator and electric unit (con-
trol unit)
DAS-158
< DTC/CIRCUIT DIAGNOSIS >
[DCA]
C1A2A ICC SENSOR POWER SUPPLY CIRCUIT
C1A2A ICC SENSOR POWER SUPPLY CIRCUIT
DTC Logic
INFOID:0000000006228098
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
PERFORM DTC CONFIRMATION PROCEDURE
1.
Start the engine.
2.
Turn the DCA system ON.
3.
Perform “All DTC Reading” with CONSULT-III.
4.
Check if the “C1A2A” is detected as the current malfunction in “Self Diagnostic Result” of “ICC/ADAS”.
Is “C1A2A” detected as the current malfunction?
YES
>> Refer to
DAS-158, "Diagnosis Procedure"
NO
>> Refer to
GI-40, "Intermittent Incident"
.
Diagnosis Procedure
INFOID:0000000006228099
1.
CHECK SELF-DIAGNOSIS RESULTS
Check if “U1000” is detected other than “C1A2A” in “Self Diagnostic Result” of “ICC/ADAS”.
Is any DTC detected?
YES
>> Perform diagnosis on the detected DTC and repair or replace the malfunctioning parts. Refer to
DAS-182, "ADAS CONTROL UNIT : DTC Logic"
NO
>> GO TO 2.
2.
CHECK ICC SENSOR SELF-DIAGNOSIS
Check if any DTC is detected in “Self Diagnostic Result” of “LASER”.
Is any DTC detected?
YES
>> Perform diagnosis on the detected DTC and repair or replace the malfunctioning parts. Refer to
.
NO
>> Replace ADAS control unit. Refer to
DAS-63, "Removal and Installation"
DTC
(On board
display)
Trouble diagnosis name
DTC detecting condition
Possible cause
C1A2A
(80)
ICC SEN PWR SUP CIR
Abnormal power supply voltage in ICC sensor
• Harness, connector, fuse
• ICC sensor
DAS
C1A33 CAN TRANSMISSION ERROR
DAS-159
< DTC/CIRCUIT DIAGNOSIS >
[DCA]
C
D
E
F
G
H
I
J
K
L
M
B
N
P
A
C1A33 CAN TRANSMISSION ERROR
DTC Logic
INFOID:0000000006228100
DTC DETECTION LOGIC
NOTE:
If DTC “C1A33” is detected along with DTC “U1000”, first diagnose the DTC “U1000”. Refer to
"ADAS CONTROL UNIT : DTC Logic"
.
DTC CONFIRMATION PROCEDURE
1.
PERFORM DTC CONFIRMATION PROCEDURE
1.
Start the engine.
2.
Turn the DCA system ON.
3.
Perform “All DTC Reading” with CONSULT-III.
4.
Check if the “C1A33” is detected as the current malfunction in “Self Diagnostic Result” of “ICC/ADAS”.
Is “C1A33” detected as the current malfunction?
YES
>> Refer to
DAS-159, "Diagnosis Procedure"
NO
>> Refer to
GI-40, "Intermittent Incident"
.
Diagnosis Procedure
INFOID:0000000006228101
1.
CHECK SELF-DIAGNOSIS RESULTS
Check if “U1000” is detected other than “C1A33” in “Self Diagnostic Result” of “ICC/ADAS”.
Is “U1000” detected?
YES
>> Perform the CAN communication system inspection. Repair or replace the malfunctioning parts.
DAS-182, "ADAS CONTROL UNIT : DTC Logic"
.
NO
>> Replace the ADAS control unit. Refer to
DAS-63, "Removal and Installation"
DTC
(On board dis-
play)
Trouble diagnosis name
DTC detecting condition
Possible causes
C1A33
(33)
CAN TRANSMISSION
ERR
If an error occurs in the CAN communication
signal that ADAS control unit transmits to ECM
ADAS control unit
DAS-160
< DTC/CIRCUIT DIAGNOSIS >
[DCA]
C1A34 COMMAND ERROR
C1A34 COMMAND ERROR
DTC Logic
INFOID:0000000006228102
DTC DETECTION LOGIC
NOTE:
If DTC “C1A34” is detected along with DTC “U1000”, first diagnose the DTC “U1000”. Refer to
"ADAS CONTROL UNIT : DTC Logic"
DTC CONFIRMATION PROCEDURE
1.
PERFORM DTC CONFIRMATION PROCEDURE
1.
Start the engine.
2.
Operate the ICC system and drive.
CAUTION:
Always drive safely.
3.
Stop the vehicle.
4.
Perform “All DTC Reading” with CONSULT-III.
5.
Check if the “C1A34” is detected as the current malfunction in “Self Diagnostic Result” of “ICC/ADAS”.
Is “C1A34” detected as the current malfunction?
YES
>> Refer to
DAS-160, "Diagnosis Procedure"
NO
>> Refer to
GI-40, "Intermittent Incident"
.
Diagnosis Procedure
INFOID:0000000006228103
1.
CHECK SELF-DIAGNOSIS RESULTS
Check if “U1000” is detected other than “C1A34” in “Self Diagnostic Result” of “ICC/ADAS”.
Is “U1000” detected?
YES
>> Perform the CAN communication system inspection. Repair or replace the malfunctioning parts.
DAS-182, "ADAS CONTROL UNIT : DTC Logic"
.
NO
>> Replace the ADAS control unit. Refer to
DAS-63, "Removal and Installation"
DTC
(On board dis-
play)
Trouble diagnosis name
DTC detecting condition
Possible causes
C1A34
(34)
COMMAND ERROR
If an error occurs in the command signal that
ADAS control unit transmits to ECM via CAN
communication
ADAS control unit
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст