Infiniti QX56 (Z62). Manual — part 740
FSU-20
< REMOVAL AND INSTALLATION >
FRONT STABILIZER
FRONT STABILIZER
Exploded View
INFOID:0000000006273961
Removal and Installation
INFOID:0000000006273962
REMOVAL
1.
Remove stabilizer connecting rod.
CAUTION:
Apply a matching mark to identify the installation position.
2.
Remove stabilizer clamps and stabilizer bushing.
3.
Remove stabilizer bar.
4.
Perform inspection after removal. Refer to
.
INSTALLATION
Note the following, and install in the reverse order of removal.
• Check the matching mark when installing.
• Install stabilizer bushing that slit becomes vehicle rear side.
• Tighten the mounting nut to the specified torque while holding a hexagonal part of stabilizer connecting rod
side.
Inspection
INFOID:0000000006273963
INSPECTION AFTER REMOVAL
Check stabilizer bar, stabilizer connecting rod, stabilizer bushing and stabilizer clamp for deformation, cracks
or damage. Replace it if necessary.
1.
Stabilizer bar
2.
Stabilizer bushing
3.
Stabilizer clamp
4.
Stabilizer connecting rod
5.
Lower link
Refer to
for symbols in the figure.
JPEIA0254GB
SERVICE DATA AND SPECIFICATIONS (SDS)
FSU-21
< SERVICE DATA AND SPECIFICATIONS (SDS)
C
D
F
G
H
I
J
K
L
M
A
B
FSU
N
O
P
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
Wheel Alignment
INFOID:0000000006225652
*1: The minimum value and maximum value is the same as the nominal value.
Measure value under unladen
*2
conditions.
*2: Fuel, engine coolant and lubricant are full. Spare tire, jack, hand tools and mats are in designated positions.
Ball Joint
INFOID:0000000006225653
Wheel Height
INFOID:0000000006225654
Item
Standard
Measurement wheel
Left side
Right side
Camber
Degree minute (Decimal degree)
Minimum
−
0
°
45
′
(
−
0.75
°
)
−
0
°
55
′
(
−
0.91
°
)
Nominal
0
°
00
′
(0.00
°
)
−
0
°
10
′
(
−
0.17
°
)
Maximum
0
°
45
′
(0.75
°
)
0
°
35
′
(0.58
°
)
Left and right difference
0
°
33
′
(0.55
°
) or less
Caster
Degree minute (Decimal degree)
Minimum
2
°
20
′
(2.34
°
)
2
°
40
′
(2.67
°
)
Nominal
3
°
05
′
(3.08
°
)
3
°
25
′
(3.42
°
)
Maximum
3
°
50
′
(3.83
°
)
4
°
10
′
(4.16
°
)
Left and right difference
0
°
45
′
(0.75
°
) or less
Kingpin inclination
Degree minute (Decimal degree)
Minimum
—
—
Nominal
13
°
20
′
(13.33
°
)
*1
13
°
25
′
(13.42
°
)
*1
Maximum
—
—
Toe-in
Total toe-in
Distance
Minimum
In 1.4 mm (0.055 in)
Nominal
In 2.4 mm (0.094 in)
Maximum
In 3.4 mm (0.134 in)
Toe angle (left wheel or right
wheel)
Degree minute (Decimal degree)
Minimum
In 0
°
03
′
(0.05
°
)
Nominal
In 0
°
05
′
(0.08
°
)
Maximum
In 0
°
07
′
(0.11
°
)
Item
Standard
Swing torque
Lower link
0.5 – 6.4 N·m (0.06 – 0.65 kg-m, 5 – 56 in-lb)
Upper link
0.5 – 4.9 N·m (0.06 – 0.49 kg-m, 5 – 43 in-lb)
Measurement on spring balance (groove position)
Lower link
11.4 – 145.4 N (1.17 – 14.83 kg, 2.57 – 32.68 lb)
Measurement on spring balance (cotter pin hole position)
Upper link
8.1 – 79.0 N (0.83 – 8.05 kg, 1.83 – 17.75 lb)
Rotating torque
Lower link
0.5 – 6.4 N·m (0.06 – 0.65 kg-m, 5 – 56 in-lb)
Upper link
0.5 – 4.9 N·m (0.06 – 0.49 kg-m, 5 – 43 in-lb)
Axial end play
0 mm (0 in)
Item
Standard
Front (Hf)
903 mm (35.55 in)
FSU-22
< SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
Measure value under unladen* conditions.
*: Fuel, engine coolant and lubricant are full. Spare tire, jack, hand tools and mats are in designated positions.
Rear (Hr)
890 mm (35.04 in)
Item
Standard
SFA746B
A
B
D
E
F
G
H
I
J
K
L
M
N
P
O
C
QUICK REFERENCE INDEX
A GENERAL INFORMATION
B ENGINE
C HYBRID
HBC
Hybrid Control System
HBB
Hybrid Battery System
HBR
Hybrid Brake System
D TRANSMISSION & DRIVE-
LINE
CL
Clutch
E SUSPENSION
F BRAKES
G STEERING
H RESTRAINTS
I
VENTILATION, HEATER &
AIR CONDITIONER
Heater & Air Conditioning System
Heater & Air Conditioning Control System
J BODY INTERIOR
K BODY EXTERIOR,
DOORS, ROOF & VEHICLE
SECURITY
HD
Hood
L DRIVER CONTROLS
M ELECTRICAL & POWER
CONTROL
Power Supply, Ground & Circuit Elements
N DRIVER INFORMATION &
MULTIMEDIA
Meter, Warning Lamp & Indicator
SN
Sonar System
Audio, Visual & Navigation System
O CRUISE CONTROL &
DRIVER ASSISTANCE
DMS
Drive Mode System
P MAINTENANCE
All rights reserved. No part
of this Service Manual may
be reproduced or stored in a
retrieval system, or transmit-
ted in any form, or by any
means, electronic, mechani-
cal, recording or otherwise,
without the prior written per-
mission of NISSAN MOTOR
CO., LTD.
Edition: May 2010
Publication No. SM1E-1Z62U0
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст