Infiniti QX56 (Z62). Manual — part 932
MIR-20
< WIRING DIAGRAM >
AUTO ANTI-DAZZLING INSIDE MIRROR SYSTEM
JCLWM5435GB
DIAGNOSIS AND REPAIR WORKFLOW
MIR-21
< BASIC INSPECTION >
C
D
E
F
G
H
I
J
K
M
A
B
MIR
N
O
P
BASIC INSPECTION
DIAGNOSIS AND REPAIR WORKFLOW
Work Flow
INFOID:0000000006257228
DETAILED FLOW
1.
OBTAIN INFORMATION ABOUT SYMPTOM
Interview the customer to obtain the malfunction information (conditions and environment when the malfunc-
tion occurred) as much as possible when the customer brings the vehicle in.
>> GO TO 2.
2.
CHECK DTC
Perform self-diagnosis for automatic drive positioner (ADP) with CONSULT-III.
Is any DTC detected?
YES
>> Refer to
NO
>> GO TO 3.
3.
REPRODUCE THE MALFUNCTION INFORMATION
Check the malfunction on the vehicle that the customer describes.
Inspect the relation of the symptoms and the condition when the symptoms occur.
>> GO TO 4.
4.
IDENTIFY THE MALFUNCTIONING SYSTEM WITH “SYMPTOM DIAGNOSIS”
Use “Symptom diagnosis” from the symptom inspection result in step 3. Then identify where to start perform-
ing the diagnosis based on possible causes and symptoms.
>> GO TO 5.
5.
IDENTIFY MALFUNCTIONING PARTS WITH “COMPONENT DIAGNOSIS”
Perform the diagnosis with “Component diagnosis” of the applicable system.
>> GO TO 6.
6.
REPAIR OR REPLACE THE MALFUNCTIONING PARTS
Repair or replace the specified malfunctioning parts.
>> GO TO 7.
7.
FINAL CHECK
Check that malfunctions are not reproduced when obtaining the malfunction information from the customer,
referring to the symptom inspection result in step 3.
Are all malfunctions corrected?
YES
>> INSPECTION END
NO
>> GO TO 4.
MIR-22
< DTC/CIRCUIT DIAGNOSIS >
DOOR MIRROR REMOTE CONTROL SWITCH
DTC/CIRCUIT DIAGNOSIS
DOOR MIRROR REMOTE CONTROL SWITCH
OPEN/CLOSE SWITCH
OPEN/CLOSE SWITCH : Component Inspection
INFOID:0000000006257229
1.
CHECK OPEN/CLOSE SWITCH
1.
Turn ignition switch OFF.
2.
Disconnect door mirror remote control switch connector.
3.
Check continuity between door mirror remote control switch terminals.
[Driver side]
[Passenger side]
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Replace door mirror remote control switch.
Door mirror remote control switch
Condition
Continuity
Terminal
12
10
Open/close switch
OPEN
Existed
13
8
12
8
CLOSE
13
10
Door mirror remote control switch
Condition
Continuity
Terminal
12
11
Open/close switch
OPEN
Existed
13
9
12
9
CLOSE
13
11
REVERSE INTERLOCK DOOR MIRROR DOES NOT OPERATE
MIR-23
< SYMPTOM DIAGNOSIS >
C
D
E
F
G
H
I
J
K
M
A
B
MIR
N
O
P
SYMPTOM DIAGNOSIS
REVERSE INTERLOCK DOOR MIRROR DOES NOT OPERATE
Diagnosis Procedure
INFOID:0000000006257230
1.
CHECK DOOR MIRROR (MANUAL FUNCTION)
Check door mirror function with door mirror remote control switch.
Refer to
ADP-126, "DOOR MIRROR : Diagnosis Procedure"
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace the malfunctioning parts.
2.
CHECK DTC
Check DTC for TCM.
Refer to
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace the malfunctioning parts.
3.
CONFIRM THE OPERATION
Confirm the operation again.
Is the result normal?
YES
>> Check intermittent incident. Refer to
GI-40, "Intermittent Incident"
.
NO
>> GO TO 1.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст