Infiniti QX56 (Z62). Manual — part 23
DOOR MIRROR REMOTE CONTROL SWITCH
ADP-85
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
H
I
K
L
M
A
B
ADP
N
O
P
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Refer to
ADP-85, "MIRROR SWITCH : Diagnosis Procedure"
.
MIRROR SWITCH : Diagnosis Procedure
INFOID:0000000006248382
1.
CHECK MIRROR SWITCH INPUT SIGNAL
1.
Turn ignition switch OFF.
2.
Disconnect door mirror remote control switch connector.
3.
Turn ignition switch ON.
4.
Check voltage between door mirror remote control switch harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> GO TO 2.
2.
CHECK MIRROR SWITCH CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect automatic drive positioner control unit connector.
3.
Check continuity between automatic drive positioner control unit harness connector and door mirror
remote control switch harness connector.
4.
Check continuity between automatic drive positioner control unit harness connector and ground.
Is the inspection result normal?
YES
>> Replace automatic drive positioner control unit.
NO
>> Repair or replace harness.
3.
CHECK DOOR MIRROR REMOTE CONTROL SWITCH GROUND CIRCUIT
MIR CON SW-RH/LH
When operating the mirror switch toward the right or left side.
: ON
Other than the above.
: OFF
Monitor item
Condition
(+)
(-)
Voltage (V)
(Approx.)
Door mirror remote control switch
Connector
Terminal
M8
4
Ground
5
5
6
14
Automatic drive positioner control unit
Door mirror remote control switch
Continuity
Connector
Terminal
Connector
Terminal
M75
3
M8
6
Existed
4
5
15
14
16
4
Automatic drive positioner control unit
Ground
Continuity
Connector
Terminal
M75
3
Not existed
4
15
16
ADP-86
< DTC/CIRCUIT DIAGNOSIS >
DOOR MIRROR REMOTE CONTROL SWITCH
1.
Turn ignition switch OFF.
2.
Check continuity between door mirror remote control switch harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace harness.
4.
CHECK MIRROR SWITCH
Check door mirror remote control switch (mirror switch).
Refer to
ADP-86, "MIRROR SWITCH : Component Inspection"
.
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Replace door mirror remote control switch (mirror switch).
5.
CHECK INTERMITTENT INCIDENT
Check intermittent incident.
Refer to
GI-40, "Intermittent Incident"
>> INSPECTION END
MIRROR SWITCH : Component Inspection
INFOID:0000000006248383
1.
CHECK MIRROR SWITCH
1.
Turn ignition switch OFF.
2.
Disconnect door mirror remote control switch connector.
3.
Check continuity between door mirror remote control switch terminals.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Replace door mirror remote control switch.
Door mirror remote control switch
Ground
Continuity
Connector
Terminal
M8
13
Existed
Door mirror remote control switch
Condition
Continuity
Terminal
4
13
Mirror switch
RIGHT
Existed
Other than the above
Not existed
5
LEFT
Existed
Other than the above
Not existed
6
UP
Existed
Other than the above
Not existed
14
DOWN
Existed
Other than the above
Not existed
POWER SEAT SWITCH GROUND CIRCUIT
ADP-87
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
H
I
K
L
M
A
B
ADP
N
O
P
POWER SEAT SWITCH GROUND CIRCUIT
Diagnosis Procedure
INFOID:0000000006248384
1.
CHECK POWER SEAT SWITCH GROUND CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect power seat switch connector.
3.
Check continuity between power seat switch harness connector and ground.
Is the inspection result normal?
YES
>> Check intermittent incident. Refer to
GI-40, "Intermittent Incident"
.
NO
>> Repair or replace harness or connector.
Power seat switch
Ground
Continuity
Connector
Terminal
B459
43
Existed
ADP-88
< DTC/CIRCUIT DIAGNOSIS >
TILT &TELESCOPIC SWITCH GROUND CIRCUIT
TILT &TELESCOPIC SWITCH GROUND CIRCUIT
Diagnosis Procedure
INFOID:0000000006248385
1.
CHECK TILT & TELESCOPIC SWITCH GROUND CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect tilt & telescopic switch connector.
3.
Check continuity between tilt & telescopic switch harness connector and ground.
Is the inspection result normal?
YES
>> Check intermittent incident. Refer to
GI-40, "Intermittent Incident"
.
NO
>> Repair or replace harness.
Tilt & telescopic switch
Ground
Continuity
Connector
Terminal
M102
1
Existed
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст