Infiniti QX56 (Z62). Manual — part 5
SYSTEM
ADP-13
< SYSTEM DESCRIPTION >
C
D
E
F
G
H
I
K
L
M
A
B
ADP
N
O
P
MANUAL FUNCTION : System Diagram
INFOID:0000000006248305
MANUAL FUNCTION : System Description
INFOID:0000000006248306
The driving position (seat, steering column and door mirror position) can be adjusted manually with power seat
switch, tilt & telescopic switch and door mirror remote control switch.
OPERATION PROCEDURE
1.
Turn ignition switch ON.
2.
Operate power seat switch, tilt & telescopic switch or door mirror remote control switch.
3.
The driver seat, steering column or door mirror operates according to the operation of each switch.
NOTE:
Seat operates only up to two places at the same time.
JMJIA3774GB
ADP-14
< SYSTEM DESCRIPTION >
SYSTEM
DETAIL FLOW
Seat
NOTE:
The power seat can be operated manually regardless of the ignition switch position.
Tilt & Telescopic
Door Mirror
NOTE:
The door mirrors can be operated manually when ignition switch is in either ACC or ON position.
MEMORY FUNCTION
Order
Input
Output
Control unit condition
1
Power seat switch
(sliding, lifting, reclin-
ing)
—
The power seat switch signal is inputted to the driver seat control
unit when the power seat switch is operated.
2
—
Motors
(sliding, lifting, reclin-
ing)
The driver seat control unit outputs signals to each motor accord-
ing to the power seat switch input signal.
Order
Input
Output
Control unit condition
1
Tilt & telescopic switch
—
The tilt & telescopic switch signal is inputted to the automatic
drive positioner control unit when the tilt & telescopic switch is op-
erated.
2
—
Motors
(Tilt, telescopic)
The automatic drive positioner control unit actuates each motor
according to the operation of the tilt & telescopic switch.
Order
Input
Output
Control unit condition
1
Door mirror remote
control switch
—
The door mirror remote control switch signal is inputted to the au-
tomatic drive positioner control unit when the door mirror remote
control switch is operated.
2
—
Motors
(Door mirror motor)
The automatic drive positioner control unit actuates each motor
according to the operation of the door mirror remote control switch.
SYSTEM
ADP-15
< SYSTEM DESCRIPTION >
C
D
E
F
G
H
I
K
L
M
A
B
ADP
N
O
P
MEMORY FUNCTION : System Diagram
INFOID:0000000006248307
MEMORY FUNCTION : System Description
INFOID:0000000006248308
The driver seat control unit can store the optimum driving positions (seat, steering column and door mirror
position) for 2 people. If the front seat position is changed, one-touch (pressing desired memory switch) oper-
ation allows changing to the other driving position.
NOTE:
Further information for the memory storage procedure. Refer to
ADP-53, "MEMORY STORING : Description"
OPERATION PROCEDURE
1.
Turn ignition switch ON.
2.
Shift position P position.
JMJIA3775GB
ADP-16
< SYSTEM DESCRIPTION >
SYSTEM
3.
Push desired memory switch.
4.
Driver seat, steering and door mirror will move to the memorized position.
OPERATION CONDITION
Satisfy all of the following items. The memory function is not performed if these items are not satisfied.
*
: When timer function does not operate.
DETAIL FLOW
TIMER FUNCTION
• The memory function can be performed for 45 seconds after opening the driver door even if the ignition
switch position is in OFF position.
• Satisfy all of the following items. The timer function is not performed if these items are not satisfied.
Item
Request status
Ignition position
ON
*
Switch inputs
• Power seat switch
• Tilt & telescopic switch
• Door mirror control switch
• Set switch
• Memory switch
OFF
(Not operated)
A/T shift selector
P position
Memory function
Registered
Vehicle speed
0 Km/h (0 MPH)
CONSULT-III
Not connected
Order
Input
Output
Control unit condition
1
Memory switch
—
The memory switch signal is inputted to the driver seat control unit
when memory switch 1 or 2 is operated.
2
—
Motors
(Seat, Steering,
door mirror)
Driver seat control unit operates each motor of seat when it recogniz-
es the memory switch pressed for 0.5 second or more and requests
each motor operation to automatic drive positioner control unit via
UART communication. The automatic drive positioner control unit op-
erates each motor.
Memory switch Indica-
tor
Driver seat control unit requests the flashing of memory indicator
while either of the motors is operating. The driver seat control unit il-
luminates the memory indicator.
3
Sensors
(Seat, steering col-
umn, door mirror)
—
Driver seat control unit judges the operating seat position with each
seat sensor input. The positions of the steering column and outside
mirror are monitored with each sensor signal. Driver seat control unit
stops the operation of each motor when each part reaches the record-
ed address.
4
—
Memory switch Indica-
tor
Driver seat control unit requests the illumination of memory indicator
after all motors stop. The driver seat control unit illuminates the mem-
ory indicator for 5 seconds.
Item
Request status
Ignition position
OFF
Set switch/memory switch
OFF
Memory function
Registered
A/T shift selector
P position
Steering lock unit status
LOCK
Driver side door switch
OFF
CUNSULT-III
Not connected
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст