Infiniti QX56 (Z62). Manual — part 908

LAN

BCM BRANCH LINE CIRCUIT

LAN-209

< DTC/CIRCUIT DIAGNOSIS >

[CAN SYSTEM (TYPE 4)]

C

D

E

F

G

H

I

J

K

L

B

A

O

P

N

BCM BRANCH LINE CIRCUIT

Diagnosis Procedure

INFOID:0000000006256380

1.

CHECK CONNECTOR

1.

Turn the ignition switch OFF.

2.

Disconnect the battery cable from the negative terminal.

3.

Check the terminals and connectors of the BCM for damage, bend and loose connection (unit side and
connector side).

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Repair the terminal and connector.

2.

CHECK HARNESS FOR OPEN CIRCUIT

1.

Disconnect the connector of BCM.

2.

Check the resistance between the BCM harness connector terminals.

Is the measurement value within the specification?

YES

>> GO TO 3.

NO

>> Repair the BCM branch line.

3.

CHECK POWER SUPPLY AND GROUND CIRCUIT

Check the power supply and the ground circuit of the BCM. Refer to

BCS-75, "Diagnosis Procedure"

.

Is the inspection result normal?

YES (Present error)>>Replace the BCM. Refer to

BCS-81, "Removal and Installation"

.

YES (Past error)>>Error was detected in the BCM branch line.
NO

>> Repair the power supply and the ground circuit.

BCM harness connector

Resistance (

Ω

)

Connector No.

Terminal No.

M68

39

40

Approx. 54 – 66

LAN-210

< DTC/CIRCUIT DIAGNOSIS >

[CAN SYSTEM (TYPE 4)]

CGW BRANCH LINE CIRCUIT (CAN COMMUNICATION CIRCUIT 1)

CGW BRANCH LINE CIRCUIT (CAN COMMUNICATION CIRCUIT 1)

Diagnosis Procedure

INFOID:0000000006256381

1.

CHECK DTC

Check DTC of the CAN gateway with CONSULT-III.
Is U1010 or B2600 indicated?

YES

>> Perform a diagnosis of the indicated DTC.

NO

>> GO TO 2.

2.

CHECK CONNECTOR

1.

Turn the ignition switch OFF.

2.

Disconnect the battery cable from the negative terminal.

3.

Check the terminals and connectors of the CAN gateway for damage, bend and loose connection (unit
side and connector side).

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Repair the terminal and connector.

3.

CHECK HARNESS FOR OPEN CIRCUIT

1.

Disconnect the connector of CAN gateway.

2.

Check the resistance between the CAN gateway harness connector terminals.

Is the measurement value within the specification?

YES

>> GO TO 4.

NO

>> Repair the CAN gateway branch line (CAN communication circuit 1). Refer to

LAN-57, "System

Diagram"

.

4.

CHECK POWER SUPPLY AND GROUND CIRCUIT

Check the power supply and the ground circuit of the CAN gateway. Refer to

LAN-116, "Diagnosis Procedure"

.

Is the inspection result normal?

YES (Present error)>>Replace the CAN gateway. Refer to

LAN-117, "Removal and Installation"

.

YES (Past error)>>Error was detected in the CAN gateway branch line (CAN communication circuit 1).
NO

>> Repair the power supply and the ground circuit.

CAN gateway harness connector

Resistance (

Ω

)

Connector No.

Terminal No.

M125

1

7

Approx. 54 – 66

LAN

CGW BRANCH LINE CIRCUIT (CAN COMMUNICATION CIRCUIT 2)

LAN-211

< DTC/CIRCUIT DIAGNOSIS >

[CAN SYSTEM (TYPE 4)]

C

D

E

F

G

H

I

J

K

L

B

A

O

P

N

CGW BRANCH LINE CIRCUIT (CAN COMMUNICATION CIRCUIT 2)

Diagnosis Procedure

INFOID:0000000006256382

1.

CHECK DTC

Check DTC of the CAN gateway with CONSULT-III.
Is U1010 or B2600 indicated?

YES

>> Perform a diagnosis of the indicated DTC.

NO

>> GO TO 2.

2.

CHECK CONNECTOR

1.

Turn the ignition switch OFF.

2.

Disconnect the battery cable from the negative terminal.

3.

Check the following terminals and connectors for damage, bend and loose connection (unit side and con-
nector side).

-

CAN gateway

-

Harness connector M19

-

Harness connector B2

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Repair the terminal and connector.

3.

CHECK HARNESS CONTINUITY (OPEN CIRCUIT)

1.

Disconnect the connector of CAN gateway.

2.

Check the continuity between the CAN gateway harness connector terminals.

Is the inspection result normal?

YES

>> GO TO 4.

NO

>> Repair the CAN gateway branch line (CAN communication circuit 2). Refer to

LAN-57, "System

Diagram"

.

4.

CHECK POWER SUPPLY AND GROUND CIRCUIT

Check the power supply and the ground circuit of the CAN gateway. Refer to

LAN-116, "Diagnosis Procedure"

.

Is the inspection result normal?

YES (Present error)>>Replace the CAN gateway. Refer to

LAN-117, "Removal and Installation"

.

YES (Past error)>>Error was detected in the CAN gateway branch line (CAN communication circuit 2).
NO

>> Repair the power supply and the ground circuit.

CAN gateway harness connector

Continuity

Connector No.

Terminal No.

M125

4

6

Existed

10

12

Existed

LAN-212

< DTC/CIRCUIT DIAGNOSIS >

[CAN SYSTEM (TYPE 4)]

DLC BRANCH LINE CIRCUIT

DLC BRANCH LINE CIRCUIT

Diagnosis Procedure

INFOID:0000000006256383

1.

CHECK CONNECTOR

1.

Turn the ignition switch OFF.

2.

Disconnect the battery cable from the negative terminal.

3.

Check the terminals and connectors of the data link connector for damage, bend and loose connection
(connector side and harness side).

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Repair the terminal and connector.

2.

CHECK HARNESS FOR OPEN CIRCUIT

Check the resistance between the data link connector terminals.

Is the measurement value within the specification?

YES (Present error)>>Check CAN system type decision again.
YES (Past error)>>Error was detected in the data link connector branch line circuit.
NO

>> Repair the data link connector branch line.

Data link connector

Resistance (

Ω

)

Connector No.

Terminal No.

M4

6

14

Approx. 54 – 66