Infiniti QX56 (Z62). Manual — part 811
REAR AUTOMATIC AIR CONDITIONING SYSTEM
HAC-135
< SYMPTOM DIAGNOSIS >
[AUTOMATIC AIR CONDITIONING]
C
D
E
F
G
H
J
K
L
M
A
B
HAC
N
O
P
REAR AUTOMATIC AIR CONDITIONING SYSTEM
Diagnosis Chart By Symptom
INFOID:0000000006275981
NOTE:
• Perform the self-diagnoses with CONSULT-III before performing the symptom diagnosis. If DTC is detected,
perform the corresponding diagnosis.
• The following table is based on the condition that front automatic air conditioning system operates normally.
Symptom
Corresponding malfunction part
Reference
• Rear air conditioning system cannot be controlled.
(Front A/C control)
• Operation status of rear air conditioning system is
not indicated on front display.
Multi AV system
Rear air conditioning sys-
tem cannot be controlled.
(Rear A/C control)
Operation status of
rear air conditioning
system is not indicated
on rear A/C control
display
• Power supply system of rear A/C
control
• Rear A/C control
HAC-115, "REAR A/C CONTROL :
Diagnosis Procedure"
Operation status of
rear air conditioning
system is indicated on
rear A/C control dis-
play
• Communication circuit between rear
A/C control and A/C auto amp.
• A/C auto amp.
HAC-127, "Diagnosis Procedure"
• Air outlet does not change.
• Rear mode door motor does not operate normally.
• Circuit between rear mode door mo-
tor and A/C auto amp.
• Rear mode door motor control link-
age
• Front mode door motor
• A/C auto amp.
HAC-116, "REAR MODE DOOR
MOTOR : Diagnosis Procedure"
• Discharge air temperature does not change.
• Rear air mix door motor does not operate normally.
• Circuit between rear air mix door
motor and A/C auto amp.
• Rear air mix door motor installation
condition
• Rear air mix door motor
• A/C auto amp.
HAC-114, "REAR AIR MIX DOOR
MOTOR : Diagnosis Procedure"
Rear blower motor operation is malfunctioning.
• Power supply system of rear blower
motor
• Circuit between rear blower motor
and A/C auto amp..
• Rear blower motor
• A/C auto amp.
HAC-131, "Diagnosis Procedure"
• Insufficient cooling.
• No cool air comes out. (Air flow volume is normal.)
• Power supply system of rear A/C re-
lay
• Circuit between rear A/C relay and
A/C auto amp..
• Circuit between rear A/C relay and
rear A/C solenoid valve.
• Circuit between rear A/C solenoid
valve and ground.
• Rear A/C relay
• Rear A/C solenoid valve
• A/C auto amp.
• Refrigerant cycle
• Air leakage from each duct
• Temperature setting trimmer (rear)
HAC-136
< SYMPTOM DIAGNOSIS >
[AUTOMATIC AIR CONDITIONING]
REAR AUTOMATIC AIR CONDITIONING SYSTEM
• Insufficient heating.
• No warm air comes out. (Air flow volume is nor-
mal.)
• Engine cooling system
• Heater hose
• Rear heater core
• Air leakage from each duct
• Temperature setting trimmer (rear)
HAC-141, "REAR AIR CONDI-
TIONER : Diagnosis Procedure"
Noise is heard when rear blower motor operates.
• Mixing any foreign object in rear
blower motor
• Rear blower motor fan breakage
• Rear blower motor rotation inferiori-
ty
HAC-132, "Component Inspection"
Symptom
Corresponding malfunction part
Reference
ACCS (ADVANCE CLIMATE CONTROL SYSTEM)
HAC-137
< SYMPTOM DIAGNOSIS >
[AUTOMATIC AIR CONDITIONING]
C
D
E
F
G
H
J
K
L
M
A
B
HAC
N
O
P
ACCS (ADVANCE CLIMATE CONTROL SYSTEM)
Symptom Table
INFOID:0000000006275982
NOTE:
• Perform the self-diagnoses with CONSULT-III before performing the symptom diagnosis. If DTC is detected,
perform the corresponding diagnosis.
• The following table is based on the condition that front automatic air conditioning system operates normally.
Symptom
Corresponding malfunction part
Reference
Auto intake switch cannot be operated. [Automatic
intake control (exhaust gas / outside odor detecting
mechanism) does not operate]
Multi AV system
Plasmacluster
™
control does not operate.
NOTE:
• Plasmacluster
™
ion technology developed by
Sharp Corporation is installed in this item.
• Plasmacluster
™
is a trademark of Sharp Corpora-
tion.
• Power supply system of ionizer
• The circuit between ionizer and A/C
auto amp.
• Ionizer
• A/C auto amp.
HAC-124, "Diagnosis Procedure"
Operation status of Plasmacluster
™
control does not
switch according to air flow.
NOTE:
• Plasmacluster
™
ion technology developed by
Sharp Corporation is installed in this item.
• Plasmacluster
™
is a trademark of Sharp Corpora-
tion.
A/C auto amp.
Replace A/C auto amp.. Refer to
HAC-146, "Removal and Installa-
tion"
.
HAC-138
< SYMPTOM DIAGNOSIS >
[AUTOMATIC AIR CONDITIONING]
INSUFFICIENT COOLING
INSUFFICIENT COOLING
FRONT AIR CONDITIONER
FRONT AIR CONDITIONER : Description
INFOID:0000000006275984
Symptom
• Insufficient cooling
• No cool air comes out. (Air flow volume is normal.)
FRONT AIR CONDITIONER : Diagnosis Procedure
INFOID:0000000006275985
NOTE:
Perform self-diagnoses with CONSULT-III before performing symptom diagnosis. If any DTC is detected, per-
form the corresponding diagnosis.
1.
CHECK MAGNET CLUTCH OPERATION
1.
Turn ignition switch ON.
2.
Operate fan switch.
3.
Press A/C switch.
4.
Check that A/C indicator turns ON. Check visually and by sound that compressor operates.
5.
Press A/C switch again.
6.
Check that A/C indicator turns OFF. Check that compressor stops.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Perform diagnosis of “COMPRESSOR DOSE NOT OPERATE” in “SYMPTOM DIAGNOSIS”.
HAC-142, "Diagnosis Procedure"
2.
CHECK DRIVE BELT
Check tension of drive belt. Refer to
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Adjust or replace drive belt depending on the inspection results.
3.
CHECK REFRIGERANT CYCLE
Connect recovery/recycling recharging equipment to the vehicle and perform pressure inspection with gauge.
Refer to
.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace parts depending on the inspection results.
4.
CHECK AIR LEAKAGE FROM EACH DUCT
Check duct and nozzle, etc. of the front air conditioning system for leakage.
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Repair or replace parts depending on the inspection results.
5.
CHECK AMBIENT TEMPERATURE DISPLAY
Check that there is not much diference between actual ambient temperature and indicated temperature on
information display in combination meter.
Is the inspection result normal?
YES
>> GO TO 6.
NO
>> Perform diagnosis for the A/C auto amp. connection recognition signal circuit. Refer to
6.
CHECK SETTING OF TEMPERATURE SETTING TRIMMER (FRONT)
1.
Check setting value of temperature setting trimmer (front). Refer to
CONDITIONING SYSTEM : Temperature Setting Trimmer (Front)"
2.
Check that temperature setting trimmer (front) is set to “+ direction”.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст